Interpretation ID: 19710.nhf

Mr. Jurgen Babirad
Rehabilitation Technology Associates, Inc.
P.O. Box 540
Kinderhook, NY 12106

Dear Mr. Babirad:

This responds to your letter requesting information regarding the modification of a 1994 Ford E-150 full size van with a lowered floor for a driver with quadriplegia. You explain that the driver was evaluated and trained by a driver rehabilitation specialist who prescribed a high-tech steering system that incorporates a reduced diameter steering wheel and reduced effort steering. Specifically, you request permission to remove the original equipment manufacturer's (OEM) steering column and steering wheel so that you may install the high tech steering system to accommodate the driver's restricted strength and range of motion.

This letter provides the relief you seek. The National Highway Traffic Safety Administration (NHTSA) will not institute enforcement proceedings against a commercial entity that modifies the steering wheel and column on a vehicle to accommodate the condition you described.

We would like to begin by explaining that NHTSA is authorized to issue Federal motor vehicle safety standards that set performance requirements for new motor vehicles and items of motor vehicle equipment. Manufacturers are required to certify that their products conform to our safety standards before they can be offered for sale. After the first sale of a vehicle, manufacturers, distributors, dealers, and repair businesses are prohibited from "knowingly making inoperative" any device or element of design installed on or in a motor vehicle in compliance with an applicable standard. In general, the "make inoperative" prohibition (49 U.S.C. 30122) requires businesses which modify motor vehicles to ensure that they do not remove, disconnect, or degrade the performance of safety equipment installed in compliance with an applicable standard. Violations of this prohibition are punishable by civil penalties of up to $1,100 per violation.

There is no procedure by which businesses petition for and are granted permission from NHTSA to modify a motor vehicle. Businesses are permitted to modify vehicles without obtaining permission from NHTSA to do so, but are subject to the make inoperative provision of 49 U.S.C. 30122. In certain limited situations, we have exercised our discretion in enforcing our requirements to provide some allowances to a business which cannot conform to our requirements when making modifications to accommodate the special needs of persons with disabilities.

Replacing the vehicle's original steering column and steering wheel and removing the driver's air bag could affect compliance with three standards: Standard No. 203, Impact protection for the driver from the steering control system, Standard No. 204, Steering control rearward displacement, and Standard No. 208, Occupant Crash Protection. For example, Standard No. 208, Occupant Crash Protection, requires vehicles to be equipped with specific manual and automatic restraint systems (e.g., seat belts and air bags) and to meet specified injury criteria during a test. Removing the air bag would affect the vehicle's compliance with Standard No. 208. However, as noted above, in situations such as this one where a vehicle must be modified to accommodate the needs of a particular disability, we have been willing to consider violations of the "make inoperative" prohibition to be justified by public need. As I have already noted above, NHTSA will not institute enforcement proceedings against a business that modifies the steering column, steering wheel, and air bag to accommodate the condition you describe.

We caution, however, that only necessary modifications should be made. In addition, you should consult with the manufacturer to determine how to disarm the air bag. The manufacturer should be able to provide information on how the modification can be safely performed. We are enclosing a warning label stating that the air bag has been deactivated. For the safety of everyone who may ride in the vehicle, we ask that you affix this label on the sun visor above the deactivated air bag. Finally, if the vehicle is sold, we urge the owner to advise the purchaser that the vehicle has been modified and consider reinstalling the removed safety equipment if appropriate.

You may be interested to know that the agency is working on a proposal to regulate the aftermarket modification of vehicles for persons with disabilities by setting out exemptions from the make inoperative prohibition only for certain standards, including Standard No. 208, and under certain conditions. In place of the agency's current approach where each request for exemption from the make inoperative prohibition is reviewed case-by-case, this proposal would give clear guidance to modifiers about principles to follow when considering vehicle modifications to accommodate someone's disabilities. We published a notice of proposed rulemaking on September 28, 1998, in the Federal Register and are in the process of reviewing public comments.

If you have other questions or require additional information, please contact Nicole Fradette of my staff at this address or by phone at (202) 366-2992.

Sincerely,
Frank Seales, Jr.
Chief Counsel
Enclosure
Warning Label
ref:VSa
d.7/1/99