Interpretation ID: 7532
7287 S. 300 E.
Midvale, UT 84047
Dear Mr. Milligan:
This responds to your letter asking about the Federal requirements that apply to the "Car Seat Support," an item you manufacture for use with infant restraints.
Background Your device appears to consist of a fabric covered block of foam approximately 18x4x3 inches in size. The marketing material you sent shows that your device is intended to be placed under the bottom rearmost edge of an installed rear-facing infant seat (bottom rearmost edge relative to the vehicle). The device would cause the restraint to tip more toward the front of the car. We understand that the device is intended for use with vehicles that have seat cushions that slant downward toward the seat back, such as in some small cars.
Infant restraints are tested by NHTSA for compliance with Federal Motor Vehicle Safety Standard (FMVSS) No. 213, Child Restraint Systems, on an approximately horizontal vehicle seat cushion. (The "standard seat assembly" used to test the restraints is specified in S7.3 of Standard No. 213, copy enclosed.) A downward- slanting vehicle seat cushion might cause an infant restraint to tip toward the rear of the car. This could result in the angle between an infant restraint's back support surface and the vertical to decrease, i.e., the back of the restraint might become more upright. If a restraint's back support surface becomes too upright, it might not be able to provide support to the infant's head and neck.
The purpose of your product is to prop the bottom of a rear-facing infant restraint when the restraint is used with a downward-slanting vehicle seat, to ensure that the restraint bottom is horizontal. You state that consumers currently use items such as "blocks of wood" and "rolled up towels" to serve the same purpose as the Car Seat Support.
NHTSA's Response There is currently no FMVSS that directly applies to the product you wish to manufacture and sell. FMVSS No. 213
applies only to new child restraint systems and not to aftermarket supporting devices.
However, there are other Federal laws that indirectly affect your manufacture and sale of the device. Under the National Traffic and Motor Vehicle Safety Act, your product is considered to be an item of motor vehicle equipment. As a manufacturer of motor vehicle equipment, you are subject to the requirements in sections 151-159 of the Safety Act concerning the recall and remedy of products with safety related defects. I have enclosed an information sheet that briefly describes those responsibilities. In the event that you or NHTSA determines that your device contain a safety- related defect, you would be responsible for notifying purchasers of the defective equipment and remedying the problem free of charge.
In addition, manufacturers, distributors, dealers, and motor vehicle repair businesses are subject to '108(a)(2)(A) of the Safety Act, which states: "No manufacturer, distributor, dealer, or motor vehicle repair business shall knowingly render inoperative ... any device or element of design installed on or in a motor vehicle or item of motor vehicle equipment in compliance with an applicable Federal motor vehicle safety standard ...." It appears unlikely from the nature of your product that it would be placed in vehicles by commercial businesses instead of child restraint owners. However, if your product were to be installed by persons in those categories, they should ensure that its installation does not compromise the safety protection provided by a child restraint system. The prohibition of '108(a)(2)(A) does not apply to the actions of vehicle owners in adding to or otherwise modifying their vehicles or items of motor vehicle equipment.
Please note that we are concerned that your device might compromise the safety protection provided by an infant seat if the consumer is not provided clear information about the use of the product. The Car Seat Support you provided came with a label that has a picture of the device positioned under a rear-facing infant seat. There is no other instruction on the label on the use of the product.
In the absence of clear instructions, there is the potential that consumers might misuse the Car Seat Support. For example, a consumer might not know that the restraint is intended for use with only a rear- facing restraint that needs a "support" to keep the bottom of the restraint horizontal when positioned on a vehicle seat. Without proper instructions, a consumer might use the Car Seat Support on an approximately horizontal vehicle seat cushion and thereby inappropriately tilt the restraint so that it does not provide sufficient crash protection. One means of reducing the likelihood of confusion about the proper use of the product would be for you to provide consumer instructions on the use of the Car Seat Support, such as on the purpose of the product, on the type of restraint and vehicle seat for which the device is intended, and on limiting how far rearward the restraint should be permitted to tilt. The picture of the Child Seat Support in use should be consistent with those instructions.
I hope this information is helpful. If you have further questions, please contact Deirdre Fujita of my staff at (202) 366-2992.
Sincerely,
Paul Jackson Rice Chief Counsel
Enclosures
ref:213 d:9/27/92