Interpretation ID: 8493
10257 Slater Ave. #103
Fountain Valley, CA 92708
Dear Mr. Higgins:
This responds to your letter of March 25, 1993 to former Chief Counsel Paul Jackson Rice seeking information on how the laws and regulations administered by this agency would apply to an item of equipment you wish to sell. According to your letter, the item is a
special clamp that is applied to the shoulder strap of a seatbelt as an after-market item. The purpose of this clamp is to allow for slack in the shoulder harness section of a seatbelt thus allowing it to be worn more comfortably.
I am pleased to have this opportunity to explain our laws and regulations to you.
The National Traffic and Motor Vehicle Safety Act (15 U.S.C. 1381 et seq.; the Safety Act) authorizes this agency to issue motor vehicle safety standards for new motor vehicles and new items of motor vehicle equipment. We have exercised this authority to establish Standard No. 208, Occupant Crash Protection (49 CFR 571.208). This standard requires new motor vehicles to be equipped with safety belts and requires that those belts meet specified fit and comfort requirements, as set forth in S7 of the standard. However, Standard No. 208 does not apply to aftermarket items that seek to alter belt fit and/or comfort. Hence, you are not required to certify that this device complies with Standard No. 208 before offering the device for sale.
In addition, you are not required to get some sort of "approval" from this agency before offering this device for sale. NHTSA has no authority to "approve" motor vehicles or motor vehicle equipment, nor do we endorse any commercial products. Instead, the Safety Act establishes a "self- certification" process under which each manufacturer is responsible for certifying that its products meet all applicable safety standards. As stated above, this device is not subject to any safety standard, so you do not have to make any certification.
Although none of our safety standards directly apply to this device, there are several provisions in the Safety Act that are relevant. Manufacturers of motor vehicle equipment such as your belt positioning device are subject to the requirements in sections 151-159 of the Safety Act (15 U.S.C. 1411-1419) concerning the recall and remedy of products with defects related to motor vehicle safety.
In addition, use of your product could be affected by section 108(a)(2)(A) of the Safety Act (15 U.S.C. 1397(a)(2)(A)). That section prohibits manufacturer, distributors, dealers, and repair shops from knowingly "rendering inoperative," in whole or in part, any device or element of design installed on or in a vehicle in compliance with an applicable safety standard. There are two elements of design in a vehicle that might be "rendered inoperative" by the use of your belt positioning device. One is the occupant protection afforded by belts that meet the specified fit and comfort requirements. The other element of design that could be rendered inoperative by the use of your device is the burn resistance required by Standard No. 302, Flammability of Interior Materials (49 CFR 571.302). The materials used in the interior of vehicles, including the seat belts, seat backs and cushions, trim panels, and headliner must comply with the burn resistance requirements of Standard No. 302 to reduce deaths and injuries in the event of a fire in the vehicle's interior. If your device renders inoperative the belt fit and comfort requirements specified in Standard No. 208 or does not comply with burn resistance requirements, it could not be installed in a vehicle by any manufacturer, distributor, dealer, or repair shop.
I note that NHTSA has received a number of inquiries about devices similar to the one you plan to sell. As we have advised others, this agency is concerned that a belted occupant could inadvertently use such products to introduce excessive slack in the upper torso belt and thereby reduce the effectiveness of that belt. We encourage you to provide instructions with the product that warn users not to introduce excessive slack and provide detailed guidance for users on what is an excessive amount of slack.
I have enclosed a general information sheet for new manufacturers that gives a thumbnail sketch of NHTSA's regulations and provides information on how to obtain copies of those regulations.
I hope you find this information helpful. If you have any other questions, please contact Mary Versailles of my staff at this address or by phone at (202) 366-2992.
Sincerely,
John Womack Acting Chief Counsel
Enclosure
ref:VSA#208 d:4/26/93