Interpretation ID: 8950
Quality Assurance Manager
Perstorp Components
Kitchener, Ontario, Canada
K2G 4R9
Dear Mr. McIntosh:
This responds to your inquiry about whether Standard No. 302, Flammability of Interior Materials (49 CFR 571.302), applies to your product. You state that you manufacture a "composite assembly acoustical abatement product" that is installed against vehicle sheet metal and is then covered by carpet, trim, or the instrument panel. You had further questions about testing your product and certifying its compliance if the Standard applies to it. I apologize for the delay in responding.
By way of background information, NHTSA is authorized to issue Federal Motor Vehicle Safety Standards that set performance requirements for new motor vehicles and items of motor vehicle equipment. NHTSA does not, however, approve or certify any vehicles or items of equipment. Instead, the National Traffic and Motor Vehicle Safety Act (The "Safety Act") establishes a "self-certification" process under which each manufacturer is responsible for certifying that its products meet all applicable safety standards. Since Standard No. 302 is a vehicle standard, the manufacturer of the vehicle, and not the manufacturer of the individual component, is responsible for certifying compliance with Standard No. 302. The agency periodically tests new vehicles and items of equipment for compliance with the standards.
Under the Safety Act's authority, NHTSA has issued Standard No. 302 which specifies burn resistance requirements for materials used in the occupant compartment of new motor vehicles. Section S4.1 lists the components in vehicle occupant compartments that the vehicle manufacturer must certify as complying with the flammability resistance requirements of paragraph S4.3. The components listed include seat cushions, seat backs, seat belts headlining, convertible tops, arm rests, all trim panels including door, front, rear, and side panels, compartment shelves, head restraints, floor coverings, sun visors, curtains, shades, wheel housing covers, engine compartment covers, and any other interior materials, including padding and crash deployed elements, that are designed to absorb energy on contact by occupants in the event of a crash. Among the listed items that might be applicable to your acoustical abatement product are floor coverings and engine compartment covers. That is, the standard would apply to your product if the acoustical abatement material is a part of one of the covered items and is within 1/2" of the occupant compartment.
You indicate in your letter that you are uncertain whether to test your product to Standard No. 302 as a composite with other materials. S4.2.2 of Standard No. 302 states, "Any material that adheres to other material(s) at every point of contact shall meet the requirements of S4.3 when tested as a composite...." You indicate in your letter that your product has multiple layers that always adhere to each other. Accordingly, assuming your product is subject to Standard No. 302, the agency would test your product as a composite material, in accordance with S4.2.2.
Please note that there are other NHTSA requirements that could affect the manufacture and sale of your product. A motor vehicle or equipment manufacturer incorporating your product in its vehicles or equipment would be subject to sections 151- 159 of the Safety Act to ensure that its vehicles or equipment do not contain any safety related defect. If the manufacturer or NHTSA determines that a safety related defect exists, the manufacturer would be responsible for notifying purchasers of the defective vehicle or equipment and remedying the problem free of charge.
In addition, section 108(a)(2)(A) of the Safety Act states: "No manufacturer, distributor, dealer, or motor vehicle repair business shall knowingly render inoperative...any device or element of design installed on or in a motor vehicle or item of motor vehicle equipment in compliance with an applicable motor vehicle safety standard..." Under this section, the entities mentioned above are required to ensure that the addition of your product would not adversely affect the compliance of any component or element of design on a vehicle with an applicable Federal safety standard. With respect to Standard No. 302, the addition of your product must not reduce the vehicle's overall flammability resistance.
I hope this information is helpful. If you have any further questions about NHTSA's safety standards, please feel free to contact Marvin Shaw of my staff at this address or by telephone at (202) 366-2992.
Sincerely,
John Womack Acting Chief Counsel
ref:302 d:4/l/94