Interpretation ID: aiam3259
Manager
Reliability & Government Standards
White Motor Corporation
35129 Curtis Boulevard
Eastlake
OH 44094;
Dear Mr. Lawrence:#This responds to your letter of January 15, 1980 which requested an interpretation of Federal Motor Vehicle Safety Standard No. 101, *Controls and Displays*. You described a control to be included in heavy duty truck tractors which would operate the cab marker lights and some of the trailer lamps and asked whether Safety Standard 101 would permit labeling of the control with the words 'marker lamps.'#We have concluded, for the reasons stated below, that Safety Standard 101 would not permit the control to be labeled in the fashion you suggest. However, it would permit labeling of the control with the symbol for clearance lamps designated therein accompanied by the words 'Clearance Lamps' or the abbreviation 'Cl Lps' and by the words 'marker lamps.'#With respect to vehicles including trucks with gross vehicle weight ratings exceeding 10,000 pounds manufactured before September 1, 1980, S4 of Safety Standard 101 permits manufacturers to comply with its requirements or with those of Safety Standard 101-80. S4.2.1 of Safety Standard 101 requires that a control which operates clearance lamps, identification lamps and/or side marker lamps be identified with the words 'Clearance Lamps' or the abbreviations 'Cl Lps' as shown in Table I Column 2 of the standard. In addition, S4.2.1 provides that such a control may also be identified by one of the symbols for clearance lamps shown in Columns 3 and 4 of Table I. (See Table I, Footnote 3.) S5.2.1 of Safety Standard 101-80 requires that such a control be labeled with the symbol for clearance lamps shown in Column 3 of Table I of the standard. However, this symbol may be accompanied by the word or abbreviation shown in Column 2 (i.e., Clearance Lamps or Cl Lps) and additional words or symbols may be used at the manufacturer's discretion for the purpose of clarity. (See Table I, Footnote 3.) The requirements of Safety Standard No. 101-80 will become mandatory and will supercede those of Safety Standard 101 for all vehicles to which it applies which are manufactured on or after September 1, 1980.#According to your product description, the control which you propose to label with the words 'marker lamps' would operate some of the trailer lamps and the cab marker lamps which also serve as clearance lamps. Thus, the control would be considered to operate clearance lamps and marker lamps and would be subject to the provisions of Safety Standard 101, Table I, Footnote 3. Accordingly, on vehicles manufactured *before* to September 1, 1980, the control you propose either must be identified in one of the following methods:#>>>1. with the words 'CLEARANCE LAMPS' or the abbreviations 'CL LPS', or#2. with the words or abbreviations shown in method number 1 above accompanied by the symbol shown in Column 3 of Table I or by the symbol shown in Column 4, Table I, of Safety Standard No. 101, or#3. with the symbol for clearance lamps shown in Column 3, Table I, of Safety Standard 101-80, or#4. with the symbol noted in method number 3 above accompanied by the words 'clearance lamps' or the abbreviations 'Cl Lps' as shown in Column 2 of Table I of Safety Standard 101-80, or#5. with the symbol and the words or abbreviations noted in method number 4 above accompanied by any additional clarifying words or symbols the manufacturer may choose.<<<#If the control you have proposed is included in vehicles manufactured on or after September 1, 1980, it must be identified as indicated in method number 3 above and may be identified as indicated in method number 4 or 5 above. Use of method number 5 above would permit use of the words 'marker lamps' in addition to the required symbol and the words 'Clearance Lamps' or the abbreviation 'Cl Lps.'#I hope that you will find this response helpful and have not been inconvenienced by our delay in sending it to you.#Sincerely, Frank Berndt, Chief Counsel;