Interpretation ID: aiam3988
387 Chestnut Street
Oneonta
NY 13820;
Dear Mr. Bagg: Thank you for your letter of July 5, 1985, to Stephen Oesch of my staf concerning Federal regulations that might affect a product you have developed. The information submitted with your letter describes the product as a collapsible partition that attaches to the rear of the front seat in a motor vehicle. The purpose of your product is to keep heat within the front portion of a car. The following discussion provides an explanation of how our standards would affect a device such as yours.; The National Traffic and Motor Vehicle Safety Act authorizes our agenc to issue Federal Motor Vehicle Safety Standards that apply to new motor vehicles and items of motor vehicle equipment. We have issued several standards that apply or affect the use of your product. First, we have issued Standard No. 205, *Glazing Materials*, which applies to all glazing installed in a motor vehicle, including the glazing used in an interior partition. Standard No. 205 incorporates by reference Standard ANS Z-26, 'Safety Code for Safety Glazing Materials for Glazing Motor Vehicles Operating on Land Highway,' of the American National Standard Institute. A copy of Standard No. 205 and ANS Z-26 are enclosed for your reference.; Standard No. 205 specifies performance requirements for various type of glazing and also regulates the locations in vehicles in which each type of glazing may be used. The various types of glazing are designated as 'Items' in the standard. Under the requirements of this standard, an interior partition to be used on a passenger vehicle at locations requisite for driving visibility, such as the device you have developed, may be manufactured out of either Item 1, Item 2, Item 4, Item 10, Item 11A, or Item 14 glazing materials.; Safety Standard No. 205 also sets forth specific certification an marking requirements for glazing materials. The marking requirements for prime glazing material manufacturers (i.e. those who fabricate, laminate, or temper the glazing material) are set out in paragraph S6.1 of the standard. In addition, section 6.3 of the standard requires each item of motor vehicle equipment to be certified pursuant to section 114 of the Vehicle Safety Act. Section 114 provides that an item of motor vehicle equipment may be certified by means of a label or tag on the item or on the outside of the container in which the equipment is delivered. The label or tag must state that the item of motor vehicle equipment complies with all applicable motor vehicle safety standards, which in this case would be Standard No. 205.; Under Section 108(a)(2)(A) of the Vehicle Safety Act, new motor vehicl equipment, such as interior partitions, must comply with applicable safety standards prior to sale. The manufacture, sale, or installation of a partition that does not conform to the standard, or the installation of a partition in a new vehicle in a location that is not authorized in Standard No. 205, would be in violation of Section 108(a)(2)(A). Under Section 109(a), anyone who sells motor vehicle equipment which does not conform to all applicable safety standards is subject to a civil penalty of up to $1,000 for each violation.; Installation of your device could also be affected by Standard No. 201 *Occupant Protection in Interior Impact*. Section 3.2 of Standard No. 201 sets energy-absorption requirements for the back of the front seat to protect the heads of rear seat occupants thrown forward in a crash. A copy of Standard No. 201 is enclosed for your reference. Therefore, if your device were installed in a new vehicle prior to its first sale to a consumer, the manufacturer would have to certify that the vehicle, as equipped, complies with all standard(sic) including Standard No. 201.; Installation of your product in a used vehicle could be affected b section 108(a)(2)(A) of the Vehicle Safety Act. In 1974, Congress amended the Vehicle Safety Act to address the problem of persons tampering with safety equipment. That section provides, in part, that:; >>>No manufacturer, distributor, dealer, or motor vehicle repai business shall knowingly render inoperative, in whole or part, any device or element of design installed on or in a motor vehicle or item of motor vehicle equipment in compliance with an applicable Federal motor vehicle safety standard . . . .<<<; Thus, no manufacturer, distributor, dealer, or motor vehicle repai business may add your product to a motor vehicle, if that action would 'render inoperative' the vehicle's compliance with Standard No. 201. The Vehicle Safety Act provides for civil penalties for persons that 'render inoperative' an element of a safety standard.; Section 108(a)(2)(A) of the Act does not apply to individual vehicl owners. Thus, individual vehicle owners can, themselves, add your product to their vehicles without violating Federal law. However, installation of your product by individual owners would have to be done in accordance with applicable State law.; Manufacturers of motor vehicle equipment also have responsibilitie under the Vehicle Safety Act regarding safety defects and noncompliances in their products. Under Sections 151 *et* *seq*., they must notify purchasers about safety-related defects and noncompliances and remedy the product free of charge. Again, Section 109(a) imposes a civil penalty upon any person who fails to provide notification of or remedy for a defect or noncompliance in motor vehicle equipment. A copy of the Vehicle Safety Act and an information sheet outlining the responsibilities of vehicle and equipment manufacturers is enclosed.; We hope you find this information helpful. Please contact this offic if you have any more questions.; Sincerely, Jeffrey R. Miller, Chief Counsel