Interpretation ID: aiam5063
OK 73108;
"Dear Mr. Barron: This responds to your inquiry about this agency' requirements that are applicable to your product, a 'UV Heat Shield.' Your sales literature explains that this product is a UV protective window film that permits between 88 to 92 percent light transmission through the front windshield. You state that the UV Heat Shield blocks ultra-violet radiation from entering the vehicle's occupant compartment. I am pleased to have this opportunity to explain our regulations to you. By way of background information, section 103 of the National Traffic and Motor Vehicle Safety Act ('Safety Act,' 15 U.S.C. 1392) authorizes NHTSA to issue safety standards for new motor vehicles and new items of motor vehicle equipment. NHTSA does not however approve or certify any vehicles or items of equipment. Instead, the Safety Act establishes a 'self-certification' process under which each manufacturer is responsible for certifying that its products meet all applicable safety standards. The agency periodically tests vehicles and items of equipment for compliance with the standards. In addition, the Safety Act requires manufacturers to recall and remedy any motor vehicle or item of motor vehicle equipment that contains a safety-related defect. Under the authority of the Safety Act, NHTSA has issued Standard No. 205, Glazing Materials, which specifies performance and location requirements for glazing used in vehicles. These requirements include specifications for minimum levels of light transmittance (e.g., 70 percent in areas requisite for driving visibility, which includes all windows in passenger cars). The purpose of this requirement is to ensure driver visibility through the windows, thereby reducing the risk of a motor vehicle crash. Manufacturers must certify that their new vehicles comply with the requirements of all applicable safety standards. If, before the vehicle were first purchased by a consumer, a subsequent manufacturer or dealer were to install your window film over the glazing, that subsequent manufacturer would be required to certify that the vehicle continues to comply with the requirements of Standard No. 205 with the window film installed. I note that while you state that your window film permits between 88 to 92 percent light transmission through the front windshield, it is the windshield with your product installed that would be required to meet the 70 percent light transmittance requirement. After a vehicle is first sold to a consumer, modifications to the vehicle are affected by 108(a)(2)(A) of the Safety Act (15 U.S.C. 1397(a)(2)(A)). That section prohibits any manufacturer, distributor, dealer, or motor vehicle repair from knowingly 'rendering inoperative' any device or element of design installed in a vehicle in compliance with any applicable safety standard. This provision means that no manufacturer, dealer, distributor, or repair business could install window tinting film if the addition of the tinting film to the glazing would result in a light transmittance of less than 70 percent, or otherwise cause the vehicle to no longer comply with the applicable requirements of Standard No. 205. Violations of this 'render inoperative' prohibition can result in Federal civil penalties to the manufacturer, dealer, distributor, or repair business of up to $1,000 for each noncomplying installation. Section 108(a)(2)(A) of the Safety Act does not affect vehicle owners. Hence, vehicle owners themselves may install tinting film or any other product on the glazing of their vehicle, regardless of whether the installation causes the vehicle to no longer comply with Standard No. 205. Individual States have the authority to regulate the operational use of vehicles by their owners, and, therefore, have the authority to regulate or preclude individual owner modifications to the glazing of their vehicles. If you are interested in further information on the provisions on the provisions of State laws, you may wish to contact the American Association of Motor Vehicle Administrators, 4600 Wilson Boulevard, Arlington, VA 22203. In addition, under the Safety Act, the UV Heat Shield would be considered an item of motor vehicle equipment. Your company, as a manufacturer of motor vehicle equipment, would be subject to the requirements in 151-159 of the Safety Act concerning the recall and remedy of products with safety related defects. In the event that NHTSA or the product's manufacturer determines that a product that is an item of motor vehicle equipment contains a safety- related defect, the manufacturer is responsible for notifying purchasers of the defective equipment and remedying the problem free of charge. I have also enclosed a general information sheet for new manufacturers which summarizes NHTSA's regulations and explains where to obtain copies of Federal motor vehicle safety standards and other regulations. I hope that you find this information helpful. If you have any other questions, please contact Marvin Shaw of my staff at this address or by phone at (202) 366-2992. Sincerely, Paul Jackson Rice Chief Counsel Enclosures";