Interpretation ID: aiam5104
Ltd. 2900 Lakeside Drive Suite 101 Santa Clara
CA 95054-2812;
"Dear Ms. Taylor: This responds to your letter seeking information o how the laws and regulations administered by this agency would apply to a device called the 'Tap Root Equipment Stand.' The equipment stand consists of a base plate which is bolted to the floor of a vehicle, a vertical tube which attaches to the base plate, and a rotating shelf at the top of the tube. The stand is intended to be used for portable equipment such as laptop computers, facsimile machines, and car phones. By way of background information, NHTSA does not provide approvals of motor vehicles or motor vehicle equipment. Under the National Traffic and Motor Vehicle Safety Act (Safety Act), it is the responsibility of the manufacturer to ensure that its motor vehicles or equipment comply with applicable Federal safety standards. The following represents our opinion based on the facts provided in your letter. NHTSA does not have any safety standards specifically covering equipment stands. However, it is possible that the installation of an equipment stand could affect the compliance of a vehicle with some safety standards. All new motor vehicles manufactured for sale in the United States must be certified by their manufacturers as complying with the applicable Federal motor vehicle safety standards. If an equipment stand is installed in a certified vehicle prior to its first sale to a customer, the person making the installation would be considered a vehicle alterer. Under our certification regulation (49 CFR Part 567), a vehicle alterer must certify that the vehicle as altered continues to comply with all applicable Federal motor vehicle safety standards. Manufacturers, distributors, dealers, or motor vehicle repair businesses modifying a used vehicle are prohibited by Section 108(a)(2)(A) of the Safety Act from knowingly rendering inoperative any safety device or element of design installed on or in a motor vehicle or item of motor vehicle equipment in compliance with an applicable Federal motor vehicle safety standard. Thus, if an equipment stand is installed in a used vehicle, any businesses making such installations cannot render inoperative the vehicle's compliance with any of our standards. In order to determine how installation of the Tap Root Equipment Stand could affect the compliance of vehicles with applicable Federal safety standards, you should carefully review each standard, including but not limited to those addressing occupant crash protection and occupant protection in interior impact. In that regard, I am enclosing for your information a fact sheet entitled Information for New Manufacturers of Motor Vehicles and Motor Vehicle Equipment, and a booklet entitled Federal Motor Vehicle Safety Standards and Regulations. By way of example, Standard No. 208, Occupant Crash Protection, requires, among other things, that passenger cars and multipurpose passenger vehicles and trucks with a GVWR of 8,500 pounds or less meet specified performance requirements in a crash test. In particular, test dummies occupying the front outboard seating positions must comply with specified injury criteria in a 30 miles per hour barrier crash test. The specified injury criteria are the head injury criteria (HIC), chest acceleration and deflection, and femur loading. Nothing in the testing requirements of Standard No. 208 explicitly prohibits the installation of an equipment stand in the interior of vehicles. However, the Tap Root Equipment Stand appears to have hard surfaces and sharp edges, especially as compared with the padded dashboard, steering wheel, seats, and other components the test dummy may contact in a crash. It may not be possible for a vehicle to satisfy the injury criteria during dynamic testing if the equipment stand was installed in an area contacted by the test dummy, or if the stand interfered with the deployment of air bags. Individual vehicle owners may modify their own vehicles without being subject to the federal safety standards. If the equipment stand is to be installed by such individual owners, however, I urge them to take potential safety hazards, such as those previously listed, into account before attempting to install the equipment stand. Manufacturers of motor vehicles and motor vehicle equipment are also subject to the defect provisions of the National Traffic and Motor Vehicle Safety Act. If data indicated that a device such as an equipment stand exposed occupants to an unreasonable risk of injury, such as from sharp edges resulting in injuries during crashes, the agency might conduct a defect investigation which could lead to a safety recall. I also note that, apart from the issue of whether the equipment stand itself posed any safety risk to vehicle occupants, it is possible that the means of installation could create problems. The manufacturer should ensure that the recommended means of installation would not result in such things as the seepage of vehicle exhaust gases into the passenger compartment or weakening of the metal floor pan. I hope this information is helpful to you and your client. If you have any further questions or need some additional information, please feel free to contact David Elias of my staff at this address or by telephone at (202) 366- 2992. Sincerely, Paul Jackson Rice Chief Counsel Enclosure";