Interpretation ID: nht93-5.17

TYPE: Interpretation-NHTSA

DATE: July 9, 1993

FROM: John Womack -- Acting Chief Counsel, NHTSA

TO: Christopher Banner

TITLE: None

ATTACHMT: Attached to letter dated 3-21-93 from Christopher Banner to John Wolmack (Womack) (OCC 8477)

TEXT:

This responds to your request for an interpretation of how NHTSA's regulations would apply to some manufacturing operations you are contemplating. I apologize for the delay in this response. In a telephone conversation with Dorothy Nakama of my staff, you explained that you would like to start producing vehicles based on Ford pickup truck chassis. Some of these Ford chassis would come from wrecked vehicles that you would strip down to the frame, and others would be new chassis that you would purchase directly from Ford. You would then install new bodies on top of some of these chassis and offer them for sale as completed vehicles. You also would like to offer some of these bodies and chassis for sale as "kit cars." In the "kit car" version, you would sell the body and chassis to the purchaser of the kit, and the purchaser of the kit would have to furnish some other parts in order to complete the vehicle.

This agency's Federal motor vehicle safety standards apply to new motor vehicles and new items of motor vehicle equipment. Federal law does not require motor vehicles and items of motor vehicle equipment to continue to comply with the safety standards after the first purchase of the vehicle or equipment item in good faith for purposes other than resale. However, Federal law does prohibit any manufacturer, distributor, dealer, or repair business from knowingly "rendering inoperative" compliance with a safety standard for a vehicle or item of equipment. See 15 U.S.C. 1397 (a)(1)(A), (a)(2)(A), and (b)(1).

1. NEW BODY ON NEW CHASSIS. All vehicles you produce by installing a new body on a new chassis would be considered new vehicles. You would have to certify that each of those vehicles conformed to all applicable safety standards. You would be considered a "final stage manufacturer" of the vehicles, as that term is used in 49 CFR Parts 567 and 568.

2. NEW BODY ON USED CHASSIS. We cannot say from the information you have provided whether the vehicles you produce by installing a new body on a stripped, wrecked Ford pickup would be treated as a new vehicle, and have to be certified as complying with the applicable safety standards. The answer depends on how extensively you modify the Ford pickup chassis.

To allow vehicle modifiers to determine when the modifications to a used chassis are so extensive that the resulting vehicle will be considered new for the purposes of the Federal safety standards, NHTSA has established specific criteria at 49 CFR 571.7(e), COMBINING NEW AND USED COMPONENTS. That section reads as follows:

When a new cab is used in the assembly of a truck, the truck will be considered newly manufactured . . . unless the engine, transmission, and drive axle(s) (as a minimum) of the assembled vehicle are not new, and at least two of these components were taken from the same vehicle.

This provision means that if you leave the frame, engine, transmission, and drive axle in place from the wrecked vehicle, and place a new body on top of it, we would consider that vehicle to be a used vehicle, which would not have to be certified by you as complying with applicable safety standards. On the other hand, if you were to remove all the drive components from the frame of the Ford pickup chassis, and add new drive components or rebuilt drive components from different vehicles, the vehicle would be a new vehicle and would have to be certified by you as complying with all applicable safety standards.

3. KIT CARS. Under the National Traffic and Motor Vehicle Safety Act, a "motor vehicle" is defined, in part, as one that is "driven by mechanical power." See 15 U.S.C. 1391(3). We have interpreted this provision to mean that a unit would be considered only an assemblage of motor vehicle equipment, and not a motor vehicle, until such time as a power source is added. None of the Federal motor vehicle safety standards apply to assemblages of motor vehicle equipment, or to used equipment items in the assemblage (items used on a vehicle previously in service on the public roads). However, certain of the safety standards would apply to new equipment items included in the assemblage. It would be a violation of Federal law if your kit car includes any new brake hoses, brake fluid, lighting equipment, tires, glazing, or seat belt assemblies that do not comply with the applicable safety standards.

If you ship your kit cars with all parts needed to produce a completed motor vehicle, including the power source, this agency will treat the kit car as a motor vehicle, not an assemblage of motor vehicle equipment, regardless of the state of completion of the kit. You would be required to certify that the kit car conformed to all applicable safety standards if it were treated as a new vehicle under the rules set forth in 1. and 2. above, but not if it were treated as a used vehicle under those rules.

I have enclosed for your information a general information sheet for manufacturers of new vehicles. This sheet highlights the relevant Federal statutes and regulations and explains how to obtain copies of them. I have also enclosed a brochure titled "Federal Motor Vehicle Safety Standards" that briefly describes each of the safety standards.

I hope this information is useful. If you have any further questions or need further information, please contact Dorothy Nakama of my staff at (202) 366-2992.