Interpretation ID: 17385.wkm

Mr. William Daws
B & W Farm Center
7581 East Monroe Road (M-46)
Breckenridge, MI 48615

Dear Mr. Daws:

Please pardon the delay in responding to your letter to Walter Myers of my staff asking whether the antilock brake system (ABS) requirements of Federal Motor Vehicle Safety Standard (Standard) No. 121, Air brake systems (49 Code of Federal Regulations (CFR) 571.121), would apply to your truck glider kits. The answer is yes.

The agency's regulation with regard to the combination of new and used components is found at 49 CFR 571.7(e), Combining new and used components (copy enclosed), which provides in pertinent part:

When a new cab is used in the assembly of a truck, the truck will be considered newly manufactured . . . unless the engine, transmission, and drive axle(s)(as a minimum) of the assembled vehicle are not new, and at least two of these components were taken from the same vehicle.

By its terms, therefore, paragraph 571.7(e) applies to specific situations in which a new cab or body is combined with used chassis components. Stated another way, the resulting vehicle will constitute a new vehicle unless the engine, transmission, and drive axle(s)are used and any two of those component came from the same vehicle. If, on the other hand, either the engine, transmission, and/or drive axle(s) are new or no two of them are from the same vehicle, then the vehicle is new. If the vehicle is considered new, it must be certified to meet all applicable safety standards (including ones requiring ABS) in effect as of the date of its manufacture (not the date the vehicle was ordered or delivered). See 49 CFR Part 567.

You also asked whether a truck is required to meet the Federal motor vehicle safety standards even if approximately 80 percent of its use will be off-road, in this case, farm use. The answer is yes.

Chapter 301 of Title 49, U.S. Code (U.S.C.)(hereinafter Act) authorizes this agency to establish Federal motor vehicle safety standards (FMVSS) applicable to new motor vehicles and new items of motor vehicle equipment. The Act defines "motor vehicle" as:

[A] vehicle driven or drawn by mechanical power and manufactured primarily for use on public streets, roads, and highways, but does not include a vehicle operated only on a rail line.

49 U.S.C. 30102(a)(6).

We have interpreted this language as follows. Vehicles that are equipped with tracks or are otherwise incapable of highway travel are plainly not motor vehicles. Agricultural equipment, such as tractors, are not motor vehicles. Further, vehicles designed and sold solely for off-road use (e.g., airport runway vehicles and underground mining vehicles) are not considered motor vehicles, even though they may be operationally capable of highway travel. On the other hand, vehicles that use the public highways on a necessary and recurring basis are motor vehicles. For instance, utility vehicles like the Jeep are plainly motor vehicles, even though they are equipped with special features to permit off-road operation. If a vehicle's greatest use will be off-road, but it will spend a substantial amount of time on-road, NHTSA has interpreted the vehicle to be a "motor vehicle." Further, if a vehicle is readily usable on the public roads and is in fact used on the public roads by a substantial number of owners, NHTSA has found the vehicle to be a motor vehicle.

Nothing in your letter suggests that your trucks should be treated any differently from any other trucks, which are clearly motor vehicles. We note that a particular customer's planned use would not ordinarily affect whether a vehicle is considered to be a motor vehicle. Moreover, even if your particular customers' planned use were relevant, 20 percent would represent a substantial amount of time on-road.

I am also enclosing for your information fact sheets entitled Information for New Manufacturers of Motor Vehicles and Motor Vehicle Equipment; Where to Obtain NHTSA's Safety Standards and Regulations; and Federal Requirements for Manufacturers of Trailers.

I hope this information is helpful to you. Should you have any further questions or need additional information, feel free to contact Mr. Myers of my staff at this address or at (202) 366-2992, fax (202) 366-3820.

Sincerely,
Frank Seales, Jr.
Chief Counsel
Enclosures
ref:121#567#568#571
d.12/4/98