Interpretation ID: 19638.nhf

Ms. Cheryl Arline
6156 Pettiford Drive
Jacksonville, FL 32209

Dear Ms. Arline:

This responds to your letter requesting an exemption from Federal Motor Vehicle Safety Standard No. 203, Impact protection for the driver from the steering control system, Standard No. 204, Steering control rearward displacement, and Standard No. 208, Occupant Crash Protection, so that your vehicle may be modified to accommodate your disability, Marquio-Brailsford disease (dwarfism). You explain that you were evaluated by a certified driver rehabilitation specialist who recommended replacing the original equipment manufacturer's (OEM) steering wheel with a reduced diameter steering wheel to accommodate your limited range of motion. The new steering wheel would be too small to be fitted with an air bag.

This letter provides the relief you seek. We can assure you that we will not institute enforcement proceedings against a commercial entity that modifies the steering wheel on a vehicle to accommodate the condition you described.

We would like to begin by explaining that the National Highway Traffic Safety Administration (NHTSA) is authorized to issue Federal motor vehicle safety standards that set performance requirements for new motor vehicles and items of motor vehicle equipment. Manufacturers are required to certify that their products conform to our safety standards before they can be offered for sale. After the first sale of a vehicle, manufacturers, distributors, dealers, and repair businesses are prohibited from "knowingly making inoperative" any device or element of design installed on or in a motor vehicle in compliance with an applicable standard. In general, the "make inoperative" prohibition (49 U.S.C. 30122) requires businesses which modify motor vehicles to ensure that they do not remove, disconnect, or degrade the performance of safety equipment installed in compliance with an applicable standard. Violations of this prohibition are punishable by civil penalties of up to $1,100 per violation.

There is no procedure by which businesses petition for and are granted permission from NHTSA to modify a motor vehicle. Businesses are permitted to modify vehicles without obtaining permission from NHTSA to do so, but are subject to the make inoperative provision of 49 U.S.C. 30122. In certain limited situations, we have exercised our discretion in enforcing our requirements to provide some allowances to a business which cannot conform to our requirements when making modifications to accommodate the special needs of persons with disabilities.

Removing the original steering wheel and replacing it with a smaller one could affect compliance with seven standards: Standard No. 101, Controls and displays, Standard No. 124, Accelerator control systems, Standard No. 203, Impact protection for the driver from the steering control system, Standard No. 204, Steering control rearward displacement, Standard No. 207, Seating systems, Standard No. 208, Occupant Crash Protection, and Standard No. 209, Seat belt assemblies. For example, Standard No. 208, Occupant Crash Protection, requires vehicles to be equipped with specific manual and automatic restraint systems (e.g., seat belts and air bags) and to meet specified injury criteria during a test. Removing the air bag would affect the vehicle's compliance with Standard No. 208. However, as noted above, in situations such as yours where a vehicle must be modified to accommodate the needs of a particular disability, we have been willing to consider violations of the "make inoperative" prohibition to be justified by public need. Accordingly, NHTSA will not institute enforcement proceedings against a business that modifies the steering wheel and air bag to accommodate your condition.

We caution, however, that only necessary modifications should be made. In addition, the person performing the modifications should consult with the manufacturer to determine how to disarm the air bag. The manufacturer should be able to provide information on how the modification can be safely performed. We are enclosing a warning label stating that the air bag has been deactivated. For the safety of everyone who may ride in the vehicle, we ask that you affix this label on the sun visor above the deactivated air bag. We encourage you to always use the vehicle's safety belts or other belt-type restraint appropriate for your disability and to recommend that other drivers and passengers buckle up as well, to improve occupant crash protection. Finally, if you sell the vehicle, we urge you to advise the purchaser that the vehicle has been modified and consider reinstalling the removed safety equipment if appropriate.

You may be interested to know that the agency is working on a proposal to regulate the aftermarket modification of vehicles for persons with disabilities by setting out exemptions from the make inoperative prohibition only for certain standards, including Standard No. 208, and under certain conditions. In place of the agency's current approach where each request for exemption from the make inoperative prohibition is reviewed case-by-case, this proposal would give clear guidance to modifiers about principles to follow when considering vehicle modifications to accommodate someone's disabilities. We published a notice of proposed rulemaking on September 28, 1998, in the Federal Register and are in the process of reviewing public comments.

You should show this letter to the dealer or repair business when you take your vehicle in to be modified. If you have other questions or require additional information, please contact Nicole Fradette of my staff at this address or by phone at (202) 366-2992.

Sincerely,
Frank Seales, Jr.
Chief Counsel
Enclosure
Warning Label
ref:VSA
d.6/25/99