Interpretation ID: 7236
President
Cleartec
1919 Paper Mill Road
Huntington Valley, PA 19006-5813
Dear Mr. Jacoby:
I have been asked to respond to your April 6, 1992 letter to former Secretary Skinner, because our agency, the National Highway Traffic Safety Administration (NHTSA), is the part of the Department of Transportation that administers the program about which you asked. Specifically, your letter asks whether there are any Federal regulations that affect a new product Cleartec has developed. The product, Clean Sweep Strips, is a transparent material applied to the windshield in a herringbone pattern, in the path of the wipers, to clean the wipers. I am pleased to have this opportunity to explain our regulations to you.
By way of background information, 103 of the National Traffic and Motor Vehicle Safety Act (Safety Act, 15 U.S.C. 1392) authorizes NHTSA to issue safety standards for new motor vehicles and new items of motor vehicle equipment. NHTSA does not, however, approve or certify any vehicles or items of equipment. Instead, the Safety Act establishes a "self-certification" process under which each manufacturer is responsible for certifying that its products meet all applicable safety standards. The agency periodically tests vehicles and items of equipment for compliance with the standards. In addition, the Safety Act requires manufacturers to recall and remedy any motor vehicle or item of motor vehicle equipment that contains a safety-related defect.
Your letter states that Clean Sweep Strips could be manufactured into new windshields. If a windshield with Clean Sweep Strips were installed as original equipment by a manufacturer of a new motor vehicle, the manufacturer would have to certify that the vehicle, with the Clean Sweep Strips installed, complies with all applicable safety standards. NHTSA has issued two safety standards, compliance with which might be affected by the installation of your Clean Sweep Strips. First, Standard No. 205, Glazing Materials, establishes a number of requirements for light transmittance, abrasion resistance, and optical deviation and visibility distortion for windshields. Second, Standard No. 104, Windshield Wiping and Washing Systems, establishes requirements for a minimum area that must be wiped by the wiping system, and the frequency at which the wiping system must operate. Any manufacturer that installed your product as original equipment on a windshield would have to certify that the windshield continued to comply with Standards No. 205 and 104 with your product installed.
After the first sale to a consumer, a vehicle is no longer required by Federal law to conform to all safety standards. However, 108(a)(2)(A) of the Safety Act provides as follows:
No manufacturer, distributor, dealer, or motor vehicle repair business shall knowingly render inoperative, in whole or part, any device or element of design installed on or in a motor vehicle or item of motor vehicle equipment in compliance with an applicable Federal motor vehicle safety standard...
This provision means that a manufacturer, dealer, distributor, or repair business cannot install your Clean Sweep Strips on any vehicle if such installation results in the vehicle no longer complying with Standard No. 205 or 104. Violations of this "render inoperative" prohibition are punishable by civil fines of up to $1,000 per violation.
I note that the "render inoperative" prohibition does not affect modifications made by vehicle owners to their own vehicles. Thus, individual vehicle owners may install your Clean Sweep Strips on their own vehicles, even if this installation causes the vehicles to no longer comply with applicable safety standards. Such installations may be regulated, however, by State law. If you are interested in further information on the provisions of State laws, you may wish to contact the American Association of Motor Vehicle Administrators, 4600 Wilson Boulevard, Arlington, Virginia 22203.
Additionally, under the Safety Act, Clean Sweep Strips would be considered an item of motor vehicle equipment. Your company, as a manufacturer of motor vehicle equipment, would be subject to the requirements in 151-159 of the Safety Act concerning the recall and remedy of products with safety defects. In the event that NHTSA or a product's manufacturer determines that a product that is an item of motor vehicle equipment contains a safety-related defect, the manufacturer is responsible for notifying purchasers of the defective equipment and remedying the problem free of charge.
Finally, I have enclosed a general information sheet for new manufacturers which summarizes NHTSA's regulations and explains where to obtain copies of Federal motor vehicle safety standards and other regulations.
I hope you find this information helpful. If you have any other questions, please contact Mary Versailles of my staff at this address or by phone at (202) 366-2992.
Sincerely,
Paul Jackson Rice Chief Counsel
Enclosure
ref:104#205 d:5/29/92