Interpretation ID: 86-4.26

TYPE: INTERPRETATION-NHTSA

DATE: 07/31/86

FROM: AUTHOR UNAVAILABLE; Erika Z. Jones; NHTSA

TO: Joseph H. Barnett, Esq.

TITLE: FMVSS INTERPRETATION

TEXT:

Joseph H. Barnett, Esq. Puckett, Barnett, Larson, Mickey Wilson & Ochsenschlager One Constitution Drive P.O. Box 1287 Aurora, Illinois 60507

Dear Mr. Barnett:

This responds to your letter concerning a brake shoe assembly invented by your client. You stated that it is contemplated that the item will be sold in the replacement or so called after market and asked whether governmental approval and/or testing is required before the invention can be marketed and placed in service. I regret the delay in responding to your letter.

By way of background information, the National Highway Traffic Safety Administration (NHTSA) does not provide approvals of motor vehicles or motor vehicle equipment. Under the National Traffic and Motor Vehicle Safety Act, it is the responsibility of the manufacturer to ensure that its vehicles or equipment comply with applicable safety standards. The following represents our opinion based on the facts provided in your letter.

NHTSA has issued safety standards for both hydraulic-braked vehicles (Standard No. 105, Hydraulic Brake Systems) and air-braked vehicles (Standard No. 121, Air Brake Systems). In the case of a brake shoe assembly, there is no applicable standard for it as a separate item of motor vehicle equipment. However, if the item is installed as original equipment on new vehicles, the vehicle manufacturer would be required to certify that the entire brake system satisfies the requirements of Standard No. 105 or Standard No. 121, as applicable. Also, if the item is added to a new motor vehicle prior to its first sale, the person who modifies the vehicle would be an alterer of a previously certified motor vehicle and would be required to certify that, as altered, the vehicle continues to comply with all of the safety standards affected by the alteration.

If the device is installed on a used vehicle by a business such as a garage, the installer would not by required to attach a certification label. However, it would have to make sure that it did not knowingly render inoperative the compliance of the vehicle with any safety standard. This is required by section 108(a) (2) (A) of the National Traffic and Motor Vehicle Safety Act.

Enclosed is an information sheet which identifies relevant Federal statutes and NHTSA standards and regulations affecting motor vehicle and motor vehicle equipment manufacturers. Please note that the Vehicle Safety Act's provisions requiring manufacturers to notify purchasers of safety-related defects and to remedy such defects without charge are applicable to motor vehicle equipment manufacturers even if their equipment is not covered by a safety standard.

Sincerely,

Erika Z. Jones Chief Counsel

Enclosure

N.H.T.A. 40O - 7th Street SW Washington, D.C. 20590

ATTN: Frank Berndt

RE: Belk Brake Assembly Patent Application Serial No. 06/804,166

Dear Mr. Berndt:

This office is counsel for George L. Belk, the inventor of an improved brake shoe assembly. I am enclosing herewith a copy of the abstract describing same along with figures 1 and 2 of the mechanical drawing submitted with the patent application.

In previous art, the webs are welded to the table and by this invention they are held together by slots and belts. Prototypes have been successfully road-tested for many thousands of miles under heavy duty conditions.

It is contemplated that the market for the item will be in the replacement or so-called attachment. Could you please advise if governmental approval and/or testing is required before the invention can be marketed and placed in service.

Very truly yours,

J.H. Barnett

JHB/me

Enclosures

BRAKE SHOE ASSEMBLY

ABSTRACT

A bake shoe assembly for a vehicle includes a generally arcuate platform, to which a pad of friction lining is attached, and with is selectively connectable to a pair of supporting webs. Each web has a plurality o radially extending peripheral projections received by corresponding slots provided in the platform. Clamp means are provided for pressing the webs against the platform such that the projections and slots cooperate to locate the webs immovably on the platform. The platform and friction lining may thereby be removed from the webs while the webs remain installed within the brake drum of the vehicle.