Interpretation ID: nht70-1.1

DATE: 04/30/70

FROM: AUTHOR UNAVAILABLE; L. R. Schneider; NHTSA

TO: David Sugarman, Esq.

TITLE: FMVSS INTERPRETATION

TEXT: In response to your letter of April 16 I enclose copies of Federal Motor Vehicle Safety Standards Nos. 107 (Reflecting Surfaces) and 108 (Lamps, Reflective Devices, and Associated Equipment). Copies of the ASTM and SAE standards cross-referenced in the Federal standards are available from the American Society for Testing and Materials and the Society of Automotive Engineers. You may find particularly helpful SAE Handbook Supplement 19, "SAF Technical Reports Referenced in Federal Motor Vehicle Safety Standards".

The answer to your first question is that Standard No. 108 requires passenger cars manufactured on or after January 1, 1970, to be equipped with a total of 4 side marker lamps and 4 side marker reflectors, one marker and one reflector, amber in color, on each side of the vehicle "as far forward as practicable", and one marker and one reflector, red in color, on each side of the vehicle, "as far to the rear as practicable" Between January 1, 1969 and January 1, 1970 the option of reflectors or markers, or a combination of the two, was permitted. Prior to January 1, 1969 the Federal lighting standard did not apply to passenger cars. I will note in passing that the rear marker lamps on the Monteverd; displayed at the recent New York show were number and must be changed to red before these vehicles are sold. There are no requirements as to size and shape of lamps and reflectors, but the SAE standards applicable to them and incorporated by reference in Standard No. 108 do set forth certain photometric requirements which must be met.

In answer to your second question, Table III of Standard No. 108 requires tail lamps to be red, but permits stop lamps and rear turn signals to be either red or amber. A proposal has been issued however (35 F.R. 106) that stop lamps be red only on passenger cars manufactured on or after January 1, 1971.

You have asked in your third question whether headlamps may be placed in the grill. The answer to this is yes, provided that this location meets the lateral spacing and height above road surface requirements of Table IV of Standard No. 108. Also, headlamps must not be covered by a grille or plastic shield when in use.

Standard No. 107 does not specify a particular color for the horn ring and hub of the steering assembly but it does specify a maximum permissible value for specular glass.

Finally, other than Standard Nos. 205 (Glazing Materials) and 212 (Windshield Mounting) which all passenger cars must meet, there is no "specific safety requirement as to the windshield" for convertibles, and there is no "requirement as to a roll bar".

Sincerely,

Enclosures April 16, 1970

U.S. Department of Transportation Federal Highway Administration

Re: F.H.W.A. Temporary Exemption

No. 69-9 issued to Automobile

Monteverdi Ltd.

September 9, 1969 expiring

August 1, 1971

Gentlemen:

I represent Automobile Monteverdi Ltd. of Switzerland. In furtherance of my letter of April 9, 1970 requesting certain information as to the above, will you inform me as to the following:

1-a)Is there a safety standard requirement with regard to lights on the side of the automobile (front and/or back); if so, is it a requirement for a light or may it be a reflector?

b) Whether it is a requirement for a light or a reflector, is there a requirement as to its size or shape?

2. With regard to rear lights, brake, safety stop and blinker; is there a specific requirement as to the color of such lights, may they be red or orange etc?

3. With regard to headlights, may the manufacturer place headlights in the grill on a two seater model and a convertible model?

4. With regard to the steering wheel is there a specific requirement that the cross bar of a steering wheel be a particular color e.g. black or grey? I know that it may not be chromed.

5. With regard to a convertible model, is there a specific safety requirement as to the windshield, and is there any requirement as to a roll bar?

I would appreciate hearing from you.

Very truly yours,

David Sugarman