Interpretation ID: nht88-3.44

TYPE: INTERPRETATION-NHTSA

DATE: 09/12/88

FROM: ERIKA Z. JONES -- NHTSA

TO: STEVE ZLOTKIN -- OVERLAND PARTS, INC.

TITLE: NONE

ATTACHMT: LETTER DATED 12/08/87 FROM STEVE ZLOTKIN TO ERIKA Z. JONES, OCC 137

TEXT: Dear Mr. Zlotkin:

This is in response to your letter seeking an interpretation of Standard No. 205, Glazing Materials (49 CFR @ 571.205). Specifically, your letter stated that your company would like to import some non-laminated windshields into the United States. I apo logize for the delay in our response. As explained below, your company is prohibited by Federal law from importing or selling this type of windshield because it does not comply with the requirements of Standard No. 205.

Standard No. 205 establishes performance and marking requirements for all glazing installed in motor vehicles. The standard incorporates by reference the requirements of Standard ANS z-26, "Safety Code for Safety Glazing Materials for Glazing Motor Vehi cles Operating on Land Highways," of the American National Standard Institute. Standard ANS Z-26 requires that glazing materials for windshields must pass a specified group of test requirements. ANS Z-26 specifies that glazing materials that comply wit h these test requirements for windshields must be marked AS-1. To date, the only glazing materials that have been marked AS-1 have been laminated safety glass. Unless your non-laminated windshields can meet the requirements for AS-1 glazing and are mar ked AS-1, they do not comply with the requirements for windshields specified in Standard ANS Z-26 or Standard No. 205. You also should be aware that Standard No. 205 permits glass-plastic glazing.

The importation and sale of noncomplying glazing would be a violation of the National Traffic and Motor Vehicle Safety Act ("Safety Act"), the statute under which Standard No. 205 was issued. Section 108(a)(1)(A) of the Safety Act provides:

No person shall manufacture for sale, sell, offer for sale, or introduce or deliver for introduction in interstate commerce, or import into the United States, any motor vehicle or item of motor vehicle equipment manufactured on or after the date any a pplicable Federal motor vehicle standard takes effect under this title unless it is in conformity with such standard...

Your letter set forth two interpretations of the law under which you suggested that your company might be able to import noncomplying windshields. Your first interpretation relied on the fact that these windshields can only be installed in vehicles that were manufactured between 1953 and 1967. Since Standard No. 205's requirements for windshields did not become effective until January 1, 1968, you suggested that the provisions of section 108(a)(1)(A) of the Safety Act might not apply, because no safet y standards were applicable to these vehicles. This suggestion is incorrect.

All windshields manufactured on or after January 1, 1968 must comply with the requirements of Standard No. 205, regardless of the year of manufacture of the vehicle on which the windshield is designed to be installed. In fact, safety standards relating to components such as brake hoses, lighting equipment, tires, glazing materials, seat belt assemblies, and wheel covers are applicable to components manufactured on or after January 1, 1968, even if those components are manufactured for motor vehicles ma nufactured before that date. In a January 16, 1987 interpretation letter to Mr. Peter Cameron-Nott (copy enclosed), the agency stated that the above listed component parts including glazing materials that were manufactured on or after January 1, 1968, w ould have to comply to the relevant safety standards (in the case of glazing, Standard No. 205) even though the underlying motor vehicle was a 1965 Jaguar.

Assuming that the non-laminated windshields that were the subject of your letter were in fact manufactured after January 1, 1968, Standard No. 205 applies to those windshields. As already noted, Section 108(a)(1)(A) of the Safety Act prohibits your comp any from importing any windshields that are subject to Standard No. 205 that do not comply with that standard.

Your second suggestion is that your company would be willing to place a sticker on these windshields to warn purchasers that the windshields do not comply with Standard No. 205. The Safety Act contains no exception to section 108(a)(1)(A)'s prohibition for noncomplying equipment, even if it were to be labeled as noncomplying. Hence, section 108(a)(1)(A) prohibits the importation of noncomplying windshields without regard to any warning labels on the windshields.

I hope this information is helpful.

ENCLOSURE