Interpretation ID: nht90-3.90

TYPE: Interpretation-NHTSA

DATE: September 10, 1990

FROM: Paul Jackson Rice -- Chief Counsel, NHTSA

TO: Harold Williams

TITLE: None

ATTACHMT: Attached to letter dated 4-3-90 from H. Williams to Chief Counsel, NHTSA (OCC 4640)

TEXT:

This responds to your letter asking about requirements on marketing your product, an aftermarket mirror wiper for truck mirrors that hooks into the truck's air system. You asked whether the National Highway Traffic Safety Administration (NHTSA) had requ irements for materials to be used with such a product. You also requested the agency send any regulations about such a product. The following discussion and the enclosed information sheet, "Information for New Manufacturers of Motor Vehicles and Equipm ent" explain your responsibility under NHTSA's regulations.

As way of background information, the National Traffic and Motor Vehicle Safety Act of 1966, as amended (the "Safety Act") authorizes this agency to issue safety standards applicable to motor vehicles and items of motor vehicle equipment. The Safety Act also requires that these safety standards establish minimum levels of performance for vehicles or equipment. Once the necessary performance level has been established, vehicle or equipment manufacturers are free to choose any means they wish to achieve the required level of performance. In other words, the safety standards do not require the use of any particular manufacturer's product or particular materials; the standards permit the use of any manufacturer's product that achieves the necessary perf ormance level. Section 114 of the Safety Act (15 U.S.C. 1403) requires manufacturers to certify that each of its vehicles or items of motor vehicle equipment complies with all applicable safety standards. Because of this provision in the law, NHTSA cann ot approve, endorse, or certify any motor vehicle or item of motor vehicle equipment.

Although NHTSA has no safety standard directly about a mirror wiper, the agency has exercised its authority to establish performance requirements for rearview mirrors installed in any new vehicle in Standard No. 111, Rearview Mirrors (49 CFR S571.111; co py enclosed). This means that vehicle manufacturers must certify that each of their new vehicles complies with the applicable requirements of Standard No. 111.

As for installation of your device on mirrors in the aftermarket, such installations are limited by section 108(a)(2)(A) of the Safety Act (15 U.S.C. 1397(a)(2)(A)). That section prohibits any manufacturer, distributor, dealer, or motor vehicle repair b usiness from knowingly rendering inoperative any device or element of design installed on or in a motor vehicle in compliance with an applicable safety standard, such as Standard No. 111. If installation of your mirror wiper resulted in a vehicle no lon ger complying with Standard No. 111, a manufacturer, distributor, dealer, or repair business that installed the mirror wiper would have rendered inoperative a device (the mirror system) installed on the vehicle in compliance Cwith Standard No. 111. To a void a "rendering

operative" violation, you should examine your product to determine if installing your mirror wiper would result in the mirror no longer complying with the Standard's requirements.

Section 109 of the Safety Act (15 U.S.C. 1398) specifies a civil penalty of up to $1,000 for each violation of the "render inoperative" provision.

Please note that the Safety Act does not establish any limitations on an individual vehicle owner's ability to alter his or her own vehicle. Under Federal law, individual owners can install any device they want on their own vehicles, regardless of whethe r that device renders inoperative the vehicle's compliance with the requirements of Standard No. 111.

Other statutory provisions in the Safety Act could affect your product. Manufacturers of motor vehicle equipment such as your mirror wiper are subject to the requirements in sections 151-159 of the Safety Act (15 U.S.C. 1411-1419) on the recall and remed y of products with defects related to motor vehicle safety. The Safety Act specifies that if either your company or this agency determines that a safety-related defect exists in your product, your company as the manufacturer must notify purchasers of th e safety-related defect and must either:

(1) repair the parts so that the defect is removed; or

(2) replace the parts with identical or reasonably equivalent parts which do not have a defect.

Whichever of these options is chosen, the manufacturer must bear the full expense and cannot charge the owner for the remedy if the equipment was purchased less than eight years before the notification campaign.

I hope this information is helpful. If you have any further questions, please feel free to contact Marvin Shaw of my staff at this address or by telephone at (202) 366-2992.