Interpretation ID: nht93-3.25

DATE: April 27, 1993

FROM: John Womack -- Acting Chief Counsel, U.S. Department of Transportation, NHTSA

TO: Lawrence Hufstedler -- Kesler Research Enterprises, LTD.; Raymond Kesler -- Kesler Research Enterprises, LTD.

TITLE: None

ATTACHMT: Attached to letter dated 4-9-93 from Lawrence Hufstedler and Raymond Kesler to John Womack (OCC 8517)

TEXT: This responds to your letter inquiring about the field-of-view requirements in Federal Motor Vehicle Safety Standard No. 111, REARVIEW MIRRORS; (49 CFR S571.111; copy enclosed) applicable to what you refer to as "passenger vehicles" weighing under 10,000 pounds. You requested a written interpretation explaining the Standard's requirements in situations where such vehicles have a left side and an interior mirror that comply with the field-of-view requirement. In particular, you wanted confirmation that in such situations a manufacturer may equip a vehicle's passenger side with any supplemental mirror or no mirror at all. You also asked whether the vehicle owner may equip a vehicle in this manner.

I am pleased to have this opportunity to explain our regulations to you. Along with a copy of Standard No. 111, I am enclosing the final rule that states the agency's decision to permit the use of convex mirrors on the exterior passenger side of passenger cars. (47 FR 38698, September 2, 1982). This notice explains the agency's regulations applicable to such convex mirrors in various situations.

By way of background, NHTSA is authorized by the National Traffic and Motor Vehicle Safety Act (Safety Act) to issue Federal motor vehicle safety standards (FMVSS's) that set performance requirements for new motor vehicles and new items of motor vehicle equipment. NHTSA is not authorized to certify or approve motor vehicles or motor vehicle equipment for compliance with the FMVSS's. Instead, under the Safety Act, each manufacturer of a motor vehicle or item of motor vehicle equipment is responsible for certifying that its products meet all applicable safety standards.

NHTSA issued Standard No. 111 to establish performance requirements for mirrors installed in each new vehicle. Section S5 of Standard No. 111 specifies the requirements applicable to mirrors installed on passenger cars. S5 requires that passenger cars be equipped with an inside rearview mirror of unit magnification and a driver's side outside rearview mirror of unit magnification that provide the field-of-view specified in S5.1.1. If the inside rearview mirror meets the field-of-view requirements of S5.1.1, then a mirror on the passenger side is not required. Please be aware that in such a situation a manufacturer could voluntarily install any type of exterior passenger side mirror, which the agency would permit as a supplemental mirror.

If the inside rearview mirror of a passenger car does not meet the field-of-view requirements of S5.1.1, then a mirror of unit magnification or a convex mirror must be installed on the passenger side. If a convex mirror is installed on the passenger side to meet the field-of-view requirements, then that convex mirror must meet certain additional requirements that are set forth

in section S5.4. These additional requirements address the convex mirror's permissible radius of curvature and an informational message that must be marked onto the mirror.

Section S6 specifies the requirements applicable to mirrors installed on multipurpose passenger vehicles (MPV's), trucks, and buses other than school buses, with a GVWR of 10,000 pounds or less. Such vehicles would comply with the standard if they are equipped with mirrors that conform to the requirements (expressed in the previous two paragraphs) that are applicable to passenger cars. Alternatively, MPV's, trucks and buses would comply with the standard if they are equipped with outside mirrors of unit magnification, each with not less than 19.5 square inches of reflective surface, on both sides of the vehicle.

Please note that the requirements of Standard No. 111 apply to new, completed vehicles and do not apply to mirrors installed as aftermarket equipment. The only limitation on aftermarket installations is set forth in section 108(a)(2)(A) of the Safety Act, which prohibits any manufacturer, distributor, dealer, or motor vehicle repair business from knowingly rendering inoperative any device or element of design installed on or in a motor vehicle or item of motor vehicle equipment in compliance with an applicable safety standard. The rearview mirror system in a vehicle is a device installed in compliance with an applicable safety standard. If the installation of an aftermarket mirror system resulted in a vehicle no longer complying with Standard No. 111, a manufacturer, distributor, dealer, or motor vehicle repair business performing the work would have rendered inoperative a device (i.e., the mirror system) installed in the vehicle in compliance with Standard No. 111, in violation of 108(a)(2)(A).

In addition to the foregoing, you should be aware that manufacturers of motor vehicle equipment, such as vehicle mirrors, are subject to the requirements in 151-159 of the Safety Act concerning the recall and remedy of products with defects relating to motor vehicle safety. If you or NHTSA determines that a safety defect exists, you must notify purchasers of your product and remedy the problem free of charge. (Note that this responsibility is borne by the vehicle manufacturer in cases in which the mirror is installed on a new vehicle by or with the express authorization of that vehicle manufacturer.) Any manufacturer that fails to provide notification of or remedy for a defect may be subject to a civil penalty of up to $1,000 per violation.

Please note that the Safety Act does not establish any limitations on an individual vehicle owner's ability to alter his or her own vehicle. Under Federal law, individual vehicle owners can install any mirror system they want on their own vehicles, regardless of whether that mirror system renders inoperative the vehicle's compliance with the requirements of Standard No. 111. However, NHTSA encourages vehicle owners not to tamper with vehicle safety equipment if the modification would degrade the safety of the vehicle.

I hope this information is helpful. Please feel free to contact Marvin Shaw of my staff at this address or by telephone at (202) 366-2992 if you have any further questions or need additional information.

Attached to Federal Register, 49 CFR, Part 571, re: Federal Motor Vehicle Safety

Standards; Rearview Mirror Systems, Final Rule, dated September 2, 1982.

(Text omitted.)