Interpretation ID: nht94-5.40

DATE: May 12, 1994

FROM: John Womack -- Acting Chief Counsel, NHTSA

TO: David Fabrycky

TITLE: None

ATTACHMT: Attached To Letter Dated 12/4/93 From David Fabrycky To NHTSA Chief Counsel (OCC-9433)

TEXT: Dear Mr. Fabrycky:

This responds to your letter about an aftermarket product you wish to manufacture. The product is a child safety seat buckle shield, which is intended to prevent a child from opening the buckle on a child restraint system. You state that your device would cover the buckle and prevent the child from gaining access to the pushbutton of a child seat buckle. To depress the pushbutton, the device requires that a latch be actuated and the cover pivoted away from the buckle. You indicated that the device requires "manual dexterity to exert the forces in many directions simultaneously."

Although we understand your concern that young children not be able to easily unbuckle a child safety seat, we have reservations about devices that interfere with the unbuckling of the seats. I hope the following discussion explains those reservations and answers the questions in your letter about the effect of our regulations on your product.

Our agency has the authority to issue safety standards applicable to new motor vehicles and new items of motor vehicle equipment. We have exercised this authority to establish Safety Standard No. 213, "Child Restraint Systems," which applies to all new child restraint systems sold in this country. However, Standard 213 does not apply to aftermarket items for child restraint systems, such as your buckle shield. Hence, you are not required to certify that this product complies with Standard 213 before selling the product.

Additionally, you are not required to get "approval" from this agency before selling the buckle shield. NHTSA has no authority to "approve" motor vehicles or motor vehicle equipment, nor do we endorse any commercial product. Instead, the National Traffic and Motor Vehicle Safety Act establishes a "self-certification" process under which each manufacturer is responsible for certifying that its products meet our safety standards. The agency periodically tests vehicles and equipment items for compliance with the standards, and also investigates alleged safety-related defects.

2

Although we do not have any standards that directly apply to your product, there are several statutory provisions that could affect it. Manufacturers of motor vehicle equipment such as your buckle shield are subject to the requirements in sections 151-159 of the Safety Act concerning the recall of products with defects related to motor vehicle safety. The agency does not determine the existence of safety defects except in the context of a defect proceeding, and thus is unable to say whether your product might or might not contain such a defect. However, the agency is concerned that people be able to easily and quickly operate a child safety seat buckle in an emergency. As the agency said in a rule on the force level necessary to operate child restraint buckles:

The agency's safety concerns over child restraint buckle force release and size stem from the need for convenient buckling and unbuckling of a child and, in emergencies, to quickly remove the child from the restraint. This latter situation can occur in instances of post-crash fires, immersions, etc. A restraint that is difficult to disengage, due to the need for excessive buckle pressure or difficulty in operating the release mechanism because of a very small release button, can unnecessarily endanger the child in the restraint and the adult attempting to release the child. (50 FR 33722; August 21, 1985)

It appears that your product could significantly increase the difficulty of using the buckle release and thus hinder a person attempting to release the belt in an emergency.

In addition, use of your product could be affected by section 108(a)(2)(A) of the Safety Act. That section prohibits commercial businesses from knowingly tampering with devices or elements of design installed in an item of motor vehicle equipment, such as a child safety seat, in compliance with the Federal motor vehicle safety standards. In determining the effect of a buckle shield on a child seat's compliance with Standard 213, NHTSA would evaluate the performance of the seat with the buckle shield installed. Standard 213 specifies several elements of design with which a child restraint system is unlikely to comply if your buckle shield were installed. Section S5.4.3.5 of Standard 213 requires the pushbutton release for any buckle on a child restraint to have a minimum area for applying the release force. Since your device will completely cover the buckle when installed, the buckle shield would cause the child restraint to no longer comply with this requirement. That section also requires the buckle to release when a specified maximum force is applied. Your device will not allow the buckle to release when the force is applied because it will cover the buckle and require force to be applied "in many directions simultaneously." Your device would thus cause the child restraint to no longer comply with that requirement. Therefore, commercial establishments cannot

3

legally install your device on customers' child safety seats. In addition, section S5.7 of Standard 213 requires each material used in a child restraint system to comply with the flammability resistance requirements of Standard 302, "Flammability of Interior Materials." If your buckle shield does not comply with the requirements of Standard 302, commercial establishments cannot legally install your device.

The prohibition of section 108(a)(2)(A) does not apply to individual vehicle owners who may install or remove any items on child restraint systems regardless of the effect on compliance with Standard 213. However, our policy is to encourage child restraint owners not to tamper with or otherwise degrade the safety of their child restraints.

I hope this information is helpful. If you have any further questions, please contact Ms. Deirdre Fujita of my staff at this address or by telephone at (202) 366-2992.

Sincerely,