Interpretation ID: 2875yy
Thomson & Weintraub
105 North Center Street
P.O. Box 3577
Bloomington, IL 61702-3577
Dear Mr. Thomson:
This responds to your letter to Dorothy Nakama of my staff in which you asked for an explanation of the responsibilities of installers and repairers of motor vehicle glazing. I apologize for the delay in this response. In a subsequent telephone conversation with Ms. Nakama, you asked that we provide a response to the following two questions:
1) Would it be a violation of Federal law if, after fixing a broken or cracked windshield, an aftermarket business still did not make the windshield comply with Federal Motor Vehicle Safety Standard No. 205?
2) What would be the consequences if an installer knowingly installed in a motor vehicle new glazing that did not comply with Standard No. 205?
Your questions are addressed below.
By way of background information, section 103 of the National Traffic and Motor Vehicle Safety Act of l966 (Safety Act, l5 U.S.C. l392) authorizes the National Highway Traffic Safety Administration (NHTSA) to issue safety standards for new motor vehicles and new motor vehicle equipment. One of the safety standards we have issued under this authority is Standard No. 205, Glazing Materials (49 CFR 571.205). Standard No. 205 establishes performance requirements for all windows (called "glazing" in the standard) in new motor vehicles and for all new replacement windows for motor vehicles.
Section 108(a)(1)(A) of the Safety Act (15 U.S.C. 1397(a)(1)(A)) specifies that no person may manufacture, import, sell, or introduce into interstate commerce any new vehicle or new replacement window that does not conform with the performance requirements of Standard No. 205. Pursuant to section 108(b)(1) of the Safety Act (15 U.S.C. 1397(b)(1)), this prohibition no longer applies to the motor vehicle after the vehicle is sold to a consumer. However, both before and after the first sale to a consumer, section 108(a)(2) of the Safety Act (15 U.S.C. 1397(a)(2)) provides that: "No manufacturer, distributor, dealer, or motor vehicle repair business shall knowingly render inoperative, in whole or in part, any device or element of design installed on or in a motor vehicle or item of motor vehicle equipment in compliance with an applicable Federal motor vehicle safety standard . . . ."
Your first question asked whether it would be a violation of Federal law if, after fixing a broken or cracked windshield (by repairing instead of replacing it), an aftermarket business still did not make the windshield comply with Federal Motor Vehicle Safety Standard No. 205. The answer depends upon whether or not the vehicle with the broken or cracked windshield has already been sold to a consumer.
If the vehicle has not yet been sold to a consumer, the "aftermarket business" would violate section 108(a)(1)(A) of the Safety Act if the vehicle with the repaired or replaced windshield did not comply with Standard No. 205 in all respects. As noted above, that section of the Safety Act prohibits any person from manufacturing, selling, importing, or introducing into interstate commerce any new vehicle that does not comply with Standard No. 205. Thus, even if a windshield is broken while a vehicle is being delivered from the factory to a new car dealer, the windshield that is in the new vehicle when it is delivered to the first purchaser must meet all requirements of Standard No. 205.
Once the vehicle has been sold to a first purchaser for purposes other than resale, any repairs or replacement of the windshield would not violate the "render inoperative" prohibition in the Safety Act. I have enclosed a September 3, l98l letter to the National Glass Dealers Association explaining that NHTSA does not consider repairing a damaged windshield to constitute rendering inoperative with respect to Standard No. 205, even if the repaired windshield does not meet the requirements of the standard once repaired. This is because the agency considers the object or event which damaged the windshield in the first place, not the repair shop, to have rendered the windshield inoperative with respect to Standard No. 205. Upon reconsideration, we reaffirm this interpretation.
Your second question asked about the consequences of an installer knowingly installing in a motor vehicle new glazing that did not comply with Standard No. 205. This would be a violation of section 108(a)(1)(A) of the Safety Act, because the installer would be introducing into interstate commerce an item of motor vehicle equipment (the windshield) that did not comply with the applicable safety standard. By so doing, the installer would be subject to a civil penalty of up to $1,000 for each time it installed a noncomplying windshield, per section 109 of the Safety Act (15 U.S.C. 1398).
I hope this information is helpful. If you have further questions or need additional information on this subject, please feel free to contact Dorothy Nakama of my staff at this address or by telephone at (202) 366-2992.
Sincerely,
Paul Jackson Rice Chief Counsel
Enclosure
/ref:205#VSA d:3/l4/9l