Interpretation ID: aiam4765
Material Management Conceptor Industries
Inc. 521 Newpark Blvd. P. O. Box 149 Newmarket
Ontario Canada L3Y 4X7;
"Dear Mr. Brush: Thank you for your letter to Mr. Clive Van Orden o our Office of Vehicle Safety Compliance seeking an interpretation of this agency's requirements for a vehicle identification number (VIN), as set forth in 49 CFR Part 565, Vehicle Identification Number - Content Requirements, and Standard No. 115, Vehicle Identification Number - Basic Requirements (49 CFR 571.115). You stated that your company plans to modify vans manufactured by General Motors (GM) to produce electric powered vehicles for sale in the United States. You asked whether these vehicles may use the GM world manufacturer identifier (WMI), as well as a check digit, model year identification, and production sequence codes assigned by GM, and use an X as the engine type code to show that the vehicles were actually manufactured by your company. As explained below, the answer to your question is no. S4.1 of Standard No. 115 reads as follows: Each vehicle manufactured in one stage shall have a VIN that is assigned by the manufacturer. Each vehicle manufactured in more than one stage shall have a VIN assigned by the incomplete vehicle manufacturer. Vehicle alterers, as specified in 49 CFR 567.7, shall utilize the VIN assigned by the original manufacturer of the vehicle. As described in your letter, Conceptor Industries plans to produce completed electric powered vehicles by using an assemblage of motor vehicle equipment produced by GM, including frame and chassis structure, steering, suspension, and braking systems. However, the assemblage provided to your company by GM would not include a power train. The absence of a power train means that this assemblage would not be an 'incomplete vehicle,' as that term is defined in S3 of Standard No. 115, so the Conceptor electric vehicles would not be considered to be manufactured in more than one stage. Your company would not qualify as a vehicle alterer, based on the information provided in your letter, because GM would not have already certified the vehicles modified by your company. Thus, the electric powered vehicles produced by Conceptor would be considered to be vehicles manufactured in one stage, and the VIN for these vehicles would have to be assigned by Conceptor, the manufacturer of these vehicles. Part 565 specifies the format and content of the VIN that Standard No. 115 requires your company to assign to its electric powered vehicles. In relevant part, 49 CFR 565.4 provides that: The VIN shall consist of four sections of characters which shall be grouped accordingly: (a) The first section shall consist of three characters which occupy positions one through three (1-3) in the VIN, This section shall uniquely identify the manufacturer, make and type of the motor vehicle if its manufacturer produces 500 or more motor vehicles of its type annually. If the manufacturer produces less than 500 motor vehicles of its type annually, those three characters, along with the third, fourth, and fifth characters of the fourth section shall uniquely identify the manufacturer, make and type of the motor vehicle. * * * Under the approach suggested in your letter, GM would be identified as the manufacturer of the vehicle by the first three characters of the VIN, and the eighth character would indicate that Conceptor was the actual manufacturer. This approach would be plainly inconsistent with the requirements of 565.4 quoted above, because the regulation requires the first three characters in the VIN to identify the vehicle manufacturer. Your company is the manufacturer of these vehicles, not GM, so your company must be identified by the first three characters of the VIN. Furthermore, 565.4(b) provides that the eighth character in the VIN shall uniquely identify specified attributes of the vehicle, not identify the manufacturer. Hence, the approach suggested in your letter would not comply with this agency's VIN requirements. Additionally, you informed Dorothy Nakama of my staff in a July 3, 1990 telelphone conversation that, at least in the initial years of your company's production of these vehicles, the annual production will be less than 500. If this is the case, you should note that 565.4(a) requires your company to use not only the first three characters of the VIN to uniquely identify the manufacturer, make and type of the motor vehicle, but also the 12th, 13th, and 14th characters of the VIN as well to make this unique identification. I hope this information is helpful. If you have any further questions or need any additional information, please feel free to contact Dorothy Nakama of my staff at this address or by telephone at (202) 366-2992. Sincerely, Paul Jackson Rice Chief Counsel";