Interpretation ID: aiam4637
CA 91724;
"Dear Mr. Blackman: This responds to your letter asking for informatio about the application of Federal safety standards to a head restraint that attaches to the rear window of pickup trucks. I hope the following information is helpful. By way of background information, the National Highway Traffic Safety Administration (NHTSA) is authorized by the National Traffic and Motor Vehicle Safety Act (the Safety Act) to issue Federal motor vehicle safety standards that set performance requirements for new motor vehicles and items of motor vehicle equipment. NHTSA is not authorized to certify or approve motor vehicles or motor vehicle equipment for compliance with our Federal motor vehicle safety standards. Instead, under the Safety Act (copy enclosed), each manufacturer of a motor vehicle or item of motor vehicle equipment is responsible for certifying that its products meet all applicable safety standards. The following represents our opinion based on our understanding of the information provided in your letter. There is currently no Federal motor vehicle safety standard that is directly applicable to the product you wish to manufacture and sell. Our standard for head restraints (Standard No. 202) applies only to completed new passenger cars and not to a head restraint device sold as an item of 'aftermarket' equipment for pickup trucks. However, there are other Federal requirements that indirectly affect your manufacture and sale of the head restraint device. Under the Safety Act, your device is considered to be an item of motor vehicle equipment. As a manufacturer of motor vehicle equipment, you are subject to the requirements in sections 151-159 of the Safety Act concerning the recall and remedy of products with defects relating to motor vehicle safety. I have enclosed an information sheet that briefly describes those responsibilities. In the event that you or NHTSA determines that your head restraints contain a safety related defect, you would be responsible for notifying purchasers of the defective equipment and remedying the problem free of charge. Safety Standard No. 302, Flammability of Interior Materials (copy enclosed), would also affect your head restraint if your product were installed by a commercial business on either new or used vehicles. A manufacturer installing your head restraint device on a new truck prior to certifying the truck as complying with all applicable Federal motor vehicle safety standards, as required by the Safety Act, has certain responsibilities relating to that obligation to certify. Standard No. 302 establishes flammability resistance requirements for trucks that must be met by certain vehicle components, including head restraints. The new vehicle manufacturer that installs your product on the new vehicle would have to certify the vehicle's compliance with Standard No. 302, and thus would be required to ensure that the head restraint device conforms to the flammability resistance requirements of the standard. A commercial business wishing to install the head restraint on new or used vehicles would be subject to statutory considerations that affect whether the business may install your product on a vehicle without violating the Safety Act. Section 108(a)(2)(A) of the Act states: 'No manufacturer, distributor, dealer, or motor vehicle repair business shall knowingly render inoperative ... any device or element of design installed on or in a motor vehicle or item of motor vehicle equipment in compliance with an applicable Federal motor vehicle safety standard ...' This section requires manufacturers, distributors, dealers or motor vehicle repair businesses (i.e., any person holding him or herself out to the public as in the business of repairing motor vehicles or motor vehicle equipment for compensation) installing your head restraint device on new or used vehicles to ensure that the addition of the apparatus would not negatively affect the compliance of any component or design on a vehicle with applicable Federal safety standards. For example, the commercial entity must ensure that the addition of the device does not degrade from the safety provided by flammable-resistant materials in the vehicle's interior compartment which have been installed in accordance with Standard No. 302. Installation of rapidly burning materials could vitiate the compliance of the materials which were present in the vehicle at the time of its sale to the first consumer and were certified as meeting FMVSS No. 302. Section 109 of the Act specifies a civil penalty of up to $1,000 for each violation of /108. However, the prohibitions of /108(a)(2)(A) do not apply to the actions of a vehicle owner in adding to or otherwise modifying his or her vehicle. Thus, a vehicle owner would not violate the Safety Act by installing the head restraint, even if doing so would negatively affect some safety feature in his or her vehicle. In addition to the materials described above, I am also enclosing a Federal Register notice (53 FR 50047) that NHTSA issued on December 13, 1988, proposing to extend the applicability of Standard No. 202 to light trucks and vans. NHTSA has proposed to make this extension effective September 1, 1991. We expect to announce the agency's next step in the rulemaking proceeding by this fall. We are also returning herewith the sketch you enclosed with your letter, as you requested in a telephone conversation with Ms. Fujita of my staff. We have issued this interpretation based on information which you confirmed you have no objection to publicly disclosing, and not on information which you asked us not to publicly disclose. Please feel free to contact us if you have further questions. Sincerely, Stephen P. Wood Acting Chief Counsel Enclosures";