Interpretation ID: 2344y
P.O. Box 2427
Salt Lake City, Utah 84110
Dear Mr. Sundstrom:
This is in response to your letter of December 9, 1989 to this office, asking us to confirm your opinion that Standard No. 302, Flammability of Interior Materials (49 CFR 571.302) does not apply to the "HOOD LOCKER" product you describe in your letter. You state that this product will be a plastic box to hold tissues which consumers may use to wipe off the engine crankcase dipstick when checking the crankcase oil. According to your letter, the product can be mounted near or on the vehicle fender well, on the under side of the hood, on the side or top of the air cleaner, or in another location near the dipstick. You believe that Standard No. 302 does not refer to the product because it will not be placed within the occupant compartment of motor vehicles and will not be placed within one-half inch of any occupant's air space. I am pleased to have this opportunity to explain our law and regulations for you.
By way of background information, the National Highway Traffic Safety Administration (NHTSA) has no authority to certify or approve motor vehicles or motor vehicle equipment for compliance with the Federal Motor Vehicle Safety Standards. Instead, the National Traffic and Motor Vehicle Safety Act (the Safety Act; 15 U.S.C. 1381 et seq.) establishes a "self-certification" process under which each manufacturer is responsible for certifying that every one of its products complies with all applicable safety standards. This agency periodically tests vehicles and items of motor vehicle equipment for compliance with the safety standards, and also investigates other alleged defects related to motor vehicle safety.
The Safety Act also gives this agency authority to issue safety standards applicable to new motor vehicles and new items of motor vehicle equipment. We have exercised this authority to establish Standard No. 302. That standard sets forth flammability resistance requirements applicable to all new motor vehicles. Therefore, any motor vehicle manufacturer that installs your "HOOD LOCKER" as original equipment in its vehicles must certify that the vehicle meets all applicable safety standards, including Standard No. 302, with the "HOOD LOCKER" installed. However, Standard No. 302 does not apply to aftermarket items of motor vehicle equipment, as your "HOOD LOCKER" appears to be. Hence, you are not required to certify that this product complies with Standard No. 302 before offering it for sale. Parenthetically, I note that your observation is correct that Standard No. 302 applies only to materials used in the occupant compartment of motor vehicles, and not to materials used in an engine compartment that is separated from the occupant compartment.
However, there are other statutory requirements that may affect this product. First, manufacturers of motor vehicle equipment such as this "HOOD LOCKER" are subject to the requirements in sections 151-159 of the Safety Act (15 U.S.C. 1411-1419) concerning the recall and remedy of products with defects related to motor vehicle safety. If either the equipment manufacturer or this agency were to determine that the "HOOD LOCKER" contained such a defect, the manufacturer would have to notify purchasers of the defect and remedy the problem free of charge to the purchasers.
Second, use of this product could be affected by section 108(a)(2)(A) of the Safety Act (15 U.S.C. 1397(a)(2)(A)). That section prohibits manufacturers, distributors, dealers, or repair shops from knowingly "rendering inoperative" devices or elements of design that were installed in a motor vehicle to comply with the Federal motor vehicle safety standards. To avoid a "rendering inoperative" violation, the above-named parties should examine the proposed installation instructions for the "HOOD LOCKER" and compare those instructions with the requirements of our safety standards, to determine if installing the "HOOD LOCKER" in accordance with those instructions would result in the vehicle no longer complying with the requirements of the safety standards. The most relevant safety standards would seem to be Standards No. 113, Hood Latch System, and 302. If the installation of the "HOOD LOCKER" would not result in a rendering inoperative of the vehicle's compliance with the safety standards, the "HOOD LOCKER" can be installed by dealers, distributors, and repair shops without violating any Federal requirements.
I trust that we have been responsive to your questions. For your information, I am enclosing an information sheet for new manufacturers of motor vehicles and motor vehicle equipment and information on how to obtain copies of motor vehicle safety standards. Please feel free to contact us if you have any further questions.
Sincerely,
Stephen P. Wood Acting Chief Counsel Enclosure /ref:VSA#302 d:3/22/90