Interpretation ID: 3235yy
Regalite Plastics Corporation
300 Needham Street
Newton Upper Falls, MA 02164
Dear Mr. Lushan:
This responds to your letter concerning the use of tinted flexible plastic glazing in certain jeep-type vehicles. You explained that a customer has asked you to manufacture a bronze-tinted clear plastic flexible window for installation in the rear side and rear windows of its vehicles. You indicated that this glazing material would not satisfy the minimum light transmittance requirement of Standard No. 205 and requested confirmation of your understanding that Standard No. 205 permits the use of such glazing for rear and side windows in these vehicles. Further, during two telephone conversations on October 29, 1991 and October 30, 1991, you informed Elizabeth Barbour of my staff that your question specifically refers to the use of this glazing on the two-door Suzuki Sidekick and the two-door Geo Tracker. You also confirmed to Ms. Barbour that the glazing materials to which your letter refers would be installed as original equipment, but added that your company is also involved with after-market products. I am pleased to have this opportunity to answer your question.
By way of background information, 103 of the National Traffic and Motor Vehicle Safety Act (Safety Act, 15 U.S.C. 1392) authorizes the National Highway Traffic Safety Administration (NHTSA) to issue safety standards for new motor vehicles and new motor vehicle equipment. NHTSA does not, however, approve or certify any vehicles or items of equipment, nor do we endorse any commercial products or processes. Instead, the Safety Act establishes a "self-certification" process under which each manufacturer is responsible for certifying that its products meet all applicable safety standards. The agency periodically tests vehicles and items of equipment for compliance with the standards, and also investigates alleged safety-related defects.
Pursuant to NHTSA's authority, the agency has established Standard No. 205, which specifies performance requirements for various types of glazing (called "items"), and specifies the locations in vehicles in which each item of glazing may be used. The standard also incorporates by reference "ANSI Z26," the American National Standards Institute's Safety Code for Safety Glazing Materials for Glazing Motor Vehicles Operating on Land Highways. Among Standard No. 205's requirements are specifications for minimum levels of light transmittance, measured by Test 2 in ANSI Z26. A minimum of 70% light transmittance is required in glazing areas requisite for driving visibility, which includes all windows in passenger cars.
In trucks, buses and multipurpose passenger vehicles, only the windshield and the windows to the immediate left and right of the driver are considered requisite for driving visibility (if they are equipped with dual outside mirrors satisfying sections S6.1(b) of FMVSS No. 111) and thus, subject to the minimum light transmittance requirement. The windows to the rear of the driver in trucks, buses and multipurpose passenger vehicles, including the rear side and rear windows, are not required to meet the light transmittance requirement. Thus, Standard No. 205 permits the use of tinted glazing materials (i.e. items of glazing that are not subject to Test 2) for windows to the rear of the driver in such vehicles when they are equipped with dual outside mirrors larger than those usually used on passenger cars.
As stated above, you described the product you wish to manufacture as tinted flexible plastic, Item 7 glazing, which would be installed in the rear side and rear windows of the two-door Suzuki Sidekick and Geo Tracker. According to the agency's information about these vehicles, the rear side and rear windows are part of a removable soft-top. Standard No. 205 permits glazing used for readily removable windows in these locations to be manufactured out of flexible plastic glazing (Items 6, 7 and 13), among other types of glazing. Thus, since these specific window locations on the two-door Suzuki Sidekick and Geo Tracker are not subject to the light transmittance requirement, and since Standard No. 205 permits use of flexible plastic glazing for readily removable windows, the Standard would permit you to manufacture the bronze-tinted flexible plastic glazing for the use your customer requested.
You also stated that your company is involved with after-market glazing materials. After a vehicle is first sold to a consumer, 108 (a)(2)(A) of the Safety Act prohibits any manufacturer, dealer, distributor, or repair business from "rendering inoperative" any device or element of design installed in a vehicle in compliance with any safety standard. According to this provision, your company, for example, could install the Item 7 glazing in the rear side and rear windows of a Suzuki Sidekick or Geo Tracker after that vehicle is first sold to a consumer. This provision would, however, prohibit the after-market installation of tinted flexible plastic glazing in the front side windows of that vehicle because such installation would cause the glazing of the front side windows to no longer comply with the requirements of Standard No. 205.
The "render inoperative" provision of the Safety Act does not apply to the actions of vehicle owners themselves. No section of the Safety Act prevents vehicle owners themselves from installing any product on their vehicles, regardless of whether the installation causes the vehicle to no longer comply with Standard No. 205. The actions of individual vehicle owners may be regulated or precluded by individual States, which have the authority to regulate owner modifications and the operational use of vehicles.
I hope this information is helpful. Please contact Elizabeth Barbour of my staff at this address or by telephone at (202) 366-2992 if you have further questions.
Sincerely,
Paul Jackson Rice Chief Counsel
ref: 205 d:ll/20/9l