Interpretation ID: nht87-3.31

TYPE: INTERPRETATION-NHTSA

DATE: 11/19/87

FROM: AUTHOR UNAVAILABLE; Erika Z. Jones; NHTSA

TO: Roger M. Cox -- R & R Lighting, Inc.

TITLE: FMVSS INTERPRETATION

ATTACHMT: 8/11/88 letter from Erika Z. Jones to J. Mike Callahan (A32; Std. 108); 4/14/87 letter from J. Mike Callahan to Taylor Vinson (occ 409); 9/3/87 letter from Erika Z. Jones to David M. Romansky

TEXT: Mr. Roger M. Cox R & R Lighting, Inc. Route 1, Box 190 Gadsden, AL 35901

Dear Mr. Cox:

This is in reply to your letter of July 8, 1987, with respect to whether a lighting product you intend to market is "in violation of any federal regulation when mounted on a motor vehicle." You describe your product as a "lighted decal" which can be mounted in the rear window of any car or pick-up truck, and the photographs you enclosed show it mounted in the center of the rear window of a pre-1980 model Seville. The decal will be wired int o the brake system and when activated by the brake "only the letters in the decal will be lighted." You state further that although the letters will appear red to an observer this product is not designed nor will it be marketed as a brake light or a tail light.

In our opinion, your product may or may not be in violation of Federal requirements depending upon the following uses. The product does not appear to be intended as a substitute for the center highmounted stop lamp that has been standard equipment on pas senger cars manufactured on or after September 1, 1985. Indeed, it could not be so used unless it met all requirements for such a lamp. The principal requirements are that such lamps have a minimum of 4 1/2 square inches of illuminated lens area, that it meet specified photometrics at 13 test points, ad that it produce a signal visible from 45 degrees from the right to the left and from five degrees up to five degrees down. If your device does not meet these requirements, removal of the lamp and replace ment with your device would violate a prohibition of the National Traffic and Motor Vehicle Safety Act against rendering inoperative equipment installed in accordance with a Federal motor vehicle safety standard, in this case Safety Standard No. 108, Lam ps, Reflective Devices, and Associated Equipment. However, a dealer could install it on a new pick-up truck, or to one side of the center lamp in a new passenger car before their initial sale, provided the device did not impair the effectiveness of the r ear lighting equipment required by Standard No. 108, and the device could be installed on some vehicles in use (cars built before September 1, 1984, and any pick-up) provided that it did not render inoperative in whole or in part other required rear ligh ting equipment.

By this we mean that the device appears allowable for these vehicles under Federal law provided that wiring it into the brake system does not reduce the stop lamp output or otherwise affect the operation or the effectiveness of the stop lamp system. You should also ensure that your product is acceptable under State and local laws as well. Because there are no Federal requirements for your product, each State may regulate it as it deems proper.

I am enclosing the samples that you enclosed, and hope that we have answered your questions.

Sincerely,

Erika Z. Jones Chief Counsel

Enclosure

R & R Lighting, Incorporated Route 1, Box 190 Gadsden, Alabama 35901

July 8, 1987

Office of Chief Counsel National Highway Traffic Safety Administration 400 7th Street, S.W. Washington, D. C. 20590

Attention: Ms. Erika Jones

Dear Mrs. Jones:

I am in the final planning stage before marketing/manufacturing a new product. After having exhausted all efforts at state and national levels, I talked with Mr. Brooks in the Office of Vehicle Safety Compliance. It was Mr. Brooks' opinion that we are no t in violation of any federal laps, but he suggested I correspond with you to get an appropriate legal opinion as to whether my product in violation of any federal regulation when mounted on a motor vehicle.

My product. the "#1-American Team Light", is a lighted decal. It is designed to be mounted in the rear window. My product can be mounted onany car or pick-up truck. It will be wired into the brake system and when activated by the brake, only the letters in the decal will be lighted. The letters will appear the same color as automobile manufacturers use in brake lights and tail lights; however, this product is not designed nor will it be marketed as a brake light or tail light. We have targeted the sport s enthusiast at high school and college level as our market group. We also feel we have a smaller market at local and state levels with a lighted decal that reads "Police" and "State Trooper".

In order to effectively market my product at its peak season, which would be September, time is of the essence. I have enclosed a sample lens and photographs.

Please review my information and sample and let me hear from you at your earliest convenience. If further information is needed, please call me collect at (205) 442-1642 or (205) 442-8436.

Very truly yours,

R & R LIGHTING INCORPORATED

Roger M. Cox

RMC/lc

Enclosures