ID: nht71-4.50

DATE: 11/17/71

FROM: AUTHOR UNAVAILABLE; J. W. Carson for E. T. Driver; NHTSA

TO: Halfpenny, Hahn & Roche

TITLE: FMVSS INTERPRETATION

TEXT: This is in reply to your letters of October 18, 1971, and November 1, 1971, to Mr. Douglas Toms, Administrator, National Highway Traffic Safety Administration, concerning the "Panic-Stop" signal system from Donel Corporation.

You are correct in your interpretation that Federal Motor Vehicle Safety Standard No. 108 is not applicable to the "Panic-Stop" system when this system is not installed on motor vehicles as original equipment. The motor vehicle laws and regulations of the individual States, are, however, applicable to the "Panic-Stop" system when sold and used as aftermarket equipment.

ID: nht71-4.6

DATE: 08/27/71

FROM: AUTHOR UNAVAILABLE; R. L. Carter; NHTSA

TO: David N. Henderson; House of Representatives

TITLE: FMVSR INTERPRETATION

TEXT: This is in reply to your letter of August 13, 1971 on behalf of the C.L.S. Car Truck Leasing Corporation of Goldsboro, North Carolina concerning the applicability of the Tire Identification and Record Keeping Regulation (49 CFR 574) to the C.L.S. Corp.

If C.L.S. leases a motor vehicle with new tires to a leasee for more than 60 days, they have the same responsibilities a tire dealer has under section 574.9. Therefore, C.L.S. is required to record the name and address of the leasee along with the tire identification number and forward this information to the tire manufacturer. See section 574.8. The person leasing the vehicle for more than 60 days is considered to be the purchaser of the tires. See section 574.3(c)(3).

If C.L.S. sells a used motor vehicle equipped with new tires to the ultimate user, they are considered a tire dealer and must meet the requirements of section 574.8. If, however, they sell a vehicle equipped with new tires to a vehicle dealer, the dealer is responsible for meeting the requirements of section 574.8 and C.L.S.'s responsibility is limited to assuring that the dealer has a means of recording the required information and forwarding it to the tire manufacturer. See section 574.8(c).

Enclosed for your convenience is a copy of the Tire Identification and Record Keeping Regulation. Thank you for your interest in auto safety.

ENC.

ID: nht71-4.7

DATE: 09/01/71

FROM: L. R. SCHNEIDER -- ACTING CHIEF COUNSEL, NHTSA; SIGNATURE BY DAVID SCHMELTZER

TO: American Jawa Inc.

TITLE: FMVSR INTERPRETATION

TEXT: This is in reply to your letter of August 17, 1971, inquiring whether tires for use on racing motorcycle are subject to the Tire Identification and Record Keeping regulation (49 C.F.R. 574).

The regulation applies to "manufacturers, . . . of new and retreaded tires for use on motor vehicles" and, thus, whether the regulation applies to the tires in question depends on whether they are for use on a "motor vehicle." If the tires are for use on a racing motorcyle (i.e., a motorcycle which is not manufactured primarily for use on the public streets, roads, and highways), the tires are not considered to be manufactured for use on a "motor vehicle" and the regulation does not apply to them. We consider a label such as "For Racing Purposes Only, Not for Highway Use" as evidence of manufacture for off road use.

The execution of an HS-7 form is unnecessary when racing tires are imported whether or not they are mounted on a racing motor-cycle. However, should it be necessary to execute an HS-7 form to expedite importation, Box 8 should be used to indicate that the items being imported are not considered to be for use on a motor vehicle and are not items of motor vehicle equipment.

ID: nht71-4.8

DATE: 09/01/71

FROM: AUTHOR UNAVAILABLE; E. T. Driver; NHTSA

TO: Latham; Pickard and Ennis

TITLE: FMVSR INTERPRETATION

TEXT: This is in reply to your letter of July 30, 1971, inquiring whether your client, American Jenbach Corporation, is required to comply with the Tire Identification and Recordkeeping regulations (49 CFR Part 574). In your letter you state that American Jenbach is engaged in the distribution of portable air compressors and pneumatic tools, the former being purchased in Europe and delivered to the plant in Burlington where tires are added to the wheels and other modifications are made. You state further that American Jenbach also reconditions compressors, and may replace tires as part of this process.

The Tire Identification and Recordkeeping regulations apply to manufacturers, brand name owners, retreaders, distributors, and dealers of new and retreaded tires for use on motor vehicles manufactured after 1948, and to manufacturers and dealers or motor vehicles manufactured after that date (49 CFR @ 574.4). Whether the regulations apply to American Jenbach depends on (1) whether the portable air compressors are motor vehicles under the National Traffic and Motor Vehicle Safety Act (15 U.S.C. 1381 et seq., hereinafter the Act) and (2) whether American Jenbach is a manufacturer, brand name owner, retreader, distributor, or dealer of new or retreaded tires, or a manufacturer or dealer of motor vehicles.

Section 102 of the Act (15 U.S.C. 1391) defines motor vehicle to mean "any vehicle driven or drawn by mechanical power manufactured primarily for use on the public streets, roads, and highways, except any vehicle operated exclusively on a rail or rails." Without additional information, such as pictures of the vehicles in question, we cannot give you a precise determination as to whether they are motor vehicles under the Act. However, the agency has determined

that portable compressors of the type that are mounted on tires for purposes of being towed on public highways are motor vehicles under the Act, and has classified them as trailers under the motor vehicle safety standards and regulations issued pursuant to the Act. As such, they are subject to the Tire Identification and Recordkeeping regulations.

Based upon your letter, it appears that American Jenbach Corporation is an importer of new portable compressors (trailers) and must meet the Tire Identification and Recordkeeping requirements applicable to motor vehicle manufacturers (section 574.10). In addition, under the Act American Jenbach may also be a distributor or dealer of these trailers and, if so, must also comply with the Tire Identification and Recordkeeping requirements applicable to dealers (section 574.9). Finally, American Jenbach would appear to be a tire dealer as to those tires that it replaces on reconditioned compressors and would be required to comply with the requirements applicable to tire dealers (section 574.7) with respect to those tires.

If the vehicles in question are motor vehicles, American Jenbach is required to comply with certain requirements in addition to the Tire Identification and Recordkeeping regulations. Trailers must conform to the requirements of Motor Vehicle Safety Standard No. 108, which deals with lighting requirements, and must be certified as conforming to all applicable standards in accordance with section 114 of the Act, and the Certification regulations. As of October 1, 1971, American Jenbach must also comply with the Defect Reports regulations (49 CFR Part-573). Copies of these requirements and a copy of the National Traffic and Motor Vehicle Safety Act are enclosed for your guidance.

If you have additional questions, please write to us.

Enclosures

ID: nht71-4.9

DATE: 09/02/71

FROM: AUTHOR UNAVAILABLE; L. R. Schneider; NHTSA

TO: Philadelphia Newspapers, Inc.

TITLE: FMVSS INTERPRETATION

TEXT: In your letter of August 18 you ask for a ruling on the permissibility of wiring one filement of a clearance lamp on your small delivery truck so that it would function as a stop lamp and turn signal lamp.

Federal Motor Vehicle Safety Standard Ho. 108, Lamps, Reflective(Illegible Words), does not prohibit combining a clearance lamp with a stop lamp or a turn signal lamp. However, the maximum allowable mounting height above the road surface for stop lamps is 72 inches measured from the center of the item with the vehicle at curb weight. There is currently no restriction on the maximum allowable mount(Illegible Words) however they may not be amounted higher than(Illegible Word) inches on vehicles manufactured on or after January 1, 1972. These restrictions, however, do not apply to supplemental lamps mounted higher than 72 or 88 inches, as long as a vehicle is equipped with stop lamps and turn signal lamps located within the mounting range prescribed by Standard No. 108,(Illegible Word) inches to 72 or 83 inches, as applicable, above the road surface.

The Federal motor vehicle safety standards do not apply to a vehicle "after the first purchase of it for purposes other than resale." If the alterations are to be made to vehicles already in the PHI fleet, the question of the legality of your modifications would be covered by regulations of the Bureau of Motor Carrier Safety, if your vehicles are subject to them, and by State and local laws.

ID: nht71-5.1

DATE: 11/17/71

FROM: AUTHOR UNAVAILABLE; J. W. Carson for E. T. Driver; NHTSA

TO: Ward School Bus Mfg., Inc.

TITLE: FMVSS INTERPRETATION

TEXT: Your letter of October 28, 1971, to Mr. Stan Haranski, Truck Body and Equipment Association, Inc., concerning switching arrangements for school bus red signal lamps, has been forwarded to this Office for reply.

Paragraph S4.1.4(a) of Federal Motor Vehicle Safety Standard No. 108 requires that the four red signal lamps be controlled by a manually actuated switch. A two-way switch, whereby all four lamps are activated when the switch is in one position, and the two rear lamps only are activated when the switch is in the opposite position, would not be in violation of this requirement of Standard No. 108.

ID: nht71-5.11

DATE: 12/02/71

FROM: AUTHOR UNAVAILABLE; Richard B. Dyson; NHTSA

TO: Lotus Cars Ltd.

TITLE: FMVSS INTERPRETATION

TEXT: This is in reply to your letter of November 16, 1971, in which you asked whether Standard No. 208 would require seat belt retractors to be installed after January 1, 1972, for the rear occasional seats of the Lotus Plan Plus Two. Our answer is that retractors will be required if the rear seats are "designated seating positions" as defined in our regulations at 49 CFR 571.3(b). The definition provides, among other things, that to be a designated seating position a seat must accomodate a 5th percentile adult female. To define an occupant of this size, the regulations incorporate a U.S. Public Health Service publication that includes the following specifications: weight, 104 pounds; standing height, 59 inches; sitting height, 30.9 inches; knee height, 17.9 inches; buttock-knee length, 20.4 inches. If the Plan Plus Two cannot accomodate a person of this size in the rear seat, it need not have a seat belt retractor for that seat. If such a person can be accomodated, then retractors will be required unless the seat is otherwise exempt by the definition as an auxiliary seating accomodation such as [a temporary or folding jump seat." We do not have the information necessary to judge whether the seat is exempt as an auxiliary seating accomodation.

Please advise us if further explanation is necessary.

ID: nht71-5.12

DATE: 12/03/71

FROM: AUTHOR UNAVAILABLE; Richard B. Dyson; NHTSA

TO: Department of California Highway Patrol

TITLE: FMVSS INTERPRETATION

TEXT: Your inquiry concerning the certification required of seat belts installed in motor vehicles manufactured after January 1, 1972, has been brought to our attention. Motor Vehicle Safety Standard No. 208, which governs the installation of seat belts, requires belts to conform to Standard No. 209. Since Standard No. 209 is amended effective January 1, 1972, your question is whether a vehicle manufactured after that date must have seat belts that are certified as conforming to the new provisions of Standard No. 209.

We construe Standard No. 208 to require only that the belts conform to Standard No. 209 as it was at the time of their manufacture. Thus, a belt manufactured before January 1 that conforms to the contemporaneous (pre-amendment) version of Standard No. 209 may be installed in a vehicle manufactured after that date. A belt manufactured after January 1, must, of course, conform to the amended version of the standard.

ID: nht71-5.13

DATE: 12/05/71

FROM: AUTHOR UNAVAILABLE; Dana L. Scott; NHTSA

TO: Hess and Eisenhardt Company

TITLE: FMVSR INTERPRETATION

TEXT: This is in response to your letter of November 12, 1971.

As correctly stated in that letter, there is no current requirement that multi-purpose passenger vehicles must comply with standards 105, 109, 110, 201, 202, 203, 204, 212, 214, 215, and 301. Additionally, the information depicted in the chart you provided is correct as of October 11, 1971. However, your dates for proposed future requirements (columns 3 and 5) may change.

The small vans and similar type vehicles being converted for use as emergency medical vehicles are required to conform to the Federal Motor Vehicle Safety Standard definition for a "multi-purpose passenger vehicle," since they utilize a truck chassis. Contrary to your opinion concerning the safety hazard of the converted emergency vehicles, we have not received any factual data indicating that these converted emergency medical vehicles constitute a safety hazard to the general public, to the sick or injured occupants, or to the attendants who must operate such vehicles.

As stated in our previous correspondence to you and Senator Robert Taft, Jr., at this point in time the Department is not in the position of proposing an expenditure for the construction of a prototype ambulance. Our limited resources are being devoted to those traffic safety programs which result in the greatest savings in lives and in the reduction of injuries.

We are retaining your correspondence for reference. If, in the future, our priorities include the development of standards relating to the design of an emergency medical vehicle, please be assured that your interests will be fully considered.

Your continued interest in our traffic safety programs is appreciated.

ID: nht71-5.14

DATE: 12/06/71

FROM: AUTHOR UNAVAILABLE; Richard B. Dyson; NHTSA

TO: Seats, Inc.

TITLE: FMVSS INTERPRETATION

TEXT: This is in reply to your letter of October 4, 1971, in which you asked our opinion as to whether Standard No. 207 permits a suspension type truck seat with fore and aft adjustment to be equipped with seat belt type webbing from the seat to the floor. It is our position that such webbing may be used to provide the strength required by Standard No. 207 and that a seat so equipped must conform to S4.2(c) of the standard (unless, as seems unlikely, the occupant's seat belt is anchored to the floor and not to the seat). Instructions for the adjustment of the seat to floor webbing are essential to the safe operation of such a system, however, and should be provided.

I apologize for any inconvenience that our delayed response may have caused you.